Olen yritänyt saada DVB-C korttia toimimaan mutta ei onnistu. Ilmeisesti Video4Linux2 driverin asetukset eivät ole kunnossa kun otsikon mukainen herja tulee testattaessa videon oletuslähdettä (multimediajärjestelmien valitsimet). Miten ongelmaa pitäisi lähteä ratkomaan?
Jos oikein olen netistä katsonut pitäisi v4l2 tukea korttiani...
Alla muutama tuloste koneeltani.
lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
0000:00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0000:00:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
0000:00:0b.0 USB Controller: NEC Corporation USB (rev 41)
0000:00:0b.1 USB Controller: NEC Corporation USB (rev 41)
0000:00:0b.2 USB Controller: NEC Corporation USB 2.0 (rev 02)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
0000:00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
0000:00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 10)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV200 QW [Radeon 7500]
lsmod
Module Size Used by
proc_intf 4100 0
freq_table 4100 0
cpufreq_userspace 4572 0
cpufreq_ondemand 6172 0
cpufreq_powersave 1920 0
radeon 69760 1
drm 59412 2 radeon
video 16260 0
sony_acpi 6280 0
pcc_acpi 11264 0
button 6800 0
battery 10244 0
container 4608 0
ac 4996 0
ipv6 229376 9
snd_via82xx 25248 2
snd_ac97_codec 64608 1 snd_via82xx
snd_pcm_oss 47652 1
snd_mixer_oss 16768 2 snd_pcm_oss
snd_pcm 84872 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_timer 23300 1 snd_pcm
tsdev 7488 0
snd_page_alloc 9604 2 snd_via82xx,snd_pcm
snd_mpu401_uart 7168 1 snd_via82xx
snd_rawmidi 22944 1 snd_mpu401_uart
snd_seq_device 8332 1 snd_rawmidi
snd 50276 9 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 9824 3 snd
usbhid 29376 0
uhci_hcd 30224 0
i2c_viapro 7436 0
via_ircc 24340 0
irda 168000 1 via_ircc
crc_ccitt 2176 1 irda
ehci_hcd 29444 0
ohci_hcd 19848 0
usbcore 107384 5 usbhid,uhci_hcd,ehci_hcd,ohci_hcd
dvb_ttpci 71948 1
dvb_core 74408 1 dvb_ttpci
saa7146_vv 44544 2 dvb_ttpci
video_buf 20484 1 saa7146_vv
saa7146 17700 2 dvb_ttpci,saa7146_vv
v4l1_compat 13572 1 saa7146_vv
v4l2_common 5888 1 saa7146_vv
videodev 9728 2 saa7146_vv
ves1820 5764 1 dvb_ttpci
stv0299 9348 1 dvb_ttpci
tda8083 5764 1 dvb_ttpci
stv0297 7424 1 dvb_ttpci
sp8870 7052 1 dvb_ttpci
firmware_class 9728 2 dvb_ttpci,sp8870
ves1x93 6404 1 dvb_ttpci
ttpci_eeprom 2688 1 dvb_ttpci
i2c_core 21264 9 i2c_viapro,dvb_ttpci,ves1820,stv0299,tda8083,stv0297,sp8870,ves1x93,ttpci_eeprom
8139cp 19200 0
8139too 24320 0
mii 4736 2 8139cp,8139too
shpchp 86116 0
pci_hotplug 30512 1 shpchp
via_agp 9216 1
agpgart 31784 2 drm,via_agp
pcspkr 3816 0
rtc 12216 0
analog 10784 0
gameport 4608 2 snd_via82xx,analog
floppy 54864 0
evdev 9088 0
md 43856 0
dm_mod 53116 1
capability 5000 0
commoncap 7808 1 capability
psmouse 19336 0
mousedev 11160 1
parport_pc 34372 1
lp 10792 0
parport 33480 2 parport_pc,lp
ide_cd 38532 0
cdrom 36508 1 ide_cd
ext3 120968 1
jbd 54168 1 ext3
ide_generic 1664 0
via82cxxx 12956 1
ide_disk 18176 3
ide_core 118988 4 ide_cd,ide_generic,via82cxxx,ide_disk
unix 26164 780
thermal 13576 0
processor 22708 1 thermal
fan 4612 0
fbcon 34048 0
font 8448 1 fbcon
bitblit 5120 1 fbcon
vesafb 6948 0
cfbcopyarea 3968 1 vesafb
cfbimgblt 3072 1 vesafb
cfbfillrect 3584 1 vesafb
dmesg
Linux version 2.6.10-5-386 (buildd@terranova) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #1 Fri Sep 23 14:13:55 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000fb880
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000fa710
ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x3fff0000
ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x3fff0030
ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x3fff00c0
ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1533.237 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 901916k/917504k available (1436k kernel code, 14980k reserved, 754k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3039.23 BogoMIPS (lpj=1519616)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 00000000 00000000
CPU: AMD Athlon(tm) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4300k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb21, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
audit: initializing netlink socket (disabled)
audit(1128773322.822:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
PCI0 UAR1 USB USB1 USB2 AC9 MC9 ILAN SLPB
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4300KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: Processor [CPU1] (supports 16 throttling states)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC35L120AVV207-1, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 241254720 sectors (123522 MB) w/7965KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4040B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Stopping tasks: ==|
Freeing memory... done (458 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 2650684k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
inserting floppy driver for 2.6.10-5-386
FDC 0 is a post-1991 82077
Real Time Clock Driver v1.12
input: PC Speaker
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 64M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: RealTek RTL8139 at 0xec00, 00:50:fc:ce:00:8e, IRQ 18
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Linux video capture interface: v1.00
saa7146: register extension 'dvb'.
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 16
saa7146: found saa7146 @ mem f8a9ec00 (revision 1, irq 16) (0x13c2,0x000a).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-CA rev1.X).
adapter has MAC addr = 00:d0:5c:04:4b:53
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 8000261f
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
DVB: registering frontend 0 (ST STV0297 DVB-C)...
dvb-ttpci: found av7110-0.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:0b.0: NEC Corporation USB
ohci_hcd 0000:00:0b.0: irq 16, pci mem 0xdfffd000
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:0b.1 -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:0b.1: NEC Corporation USB (#2)
ohci_hcd 0000:00:0b.1: irq 17, pci mem 0xdfffe000
ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:0b.2[C] -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:0b.2: NEC Corporation USB 2.0
ehci_hcd 0000:00:0b.2: irq 18, pci mem 0xdffffe00
ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:0b.2: USB 2.0 initialized, EHCI 0.95, driver 26 Oct 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 5 ports detected
irda_init()
NET: Registered protocol family 23
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:11.2: irq 5, io base 0xdc00
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:11.3: irq 5, io base 0xe000
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.4[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.4: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:11.4: irq 5, io base 0xe400
uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 6
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb 4-1: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:11.2-1
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:11.2-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ts: Compaq touchscreen protocol output
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
apm: BIOS not found.
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.14.0 20050125 on minor 0: ATI Technologies Inc Radeon RV200 QW [Radeon 7500]
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
eth0: no IPv6 routers present
-Jere
Aihe: Koeputken "Video for Linux 2 (v4l2)" luominen epäonnistui (Luettu 2484 kertaa)
