Ongelmia Hauppauge Nova-T Stickin kaukosäätimen kanssa

[runeh]

Juu myönnetään pihalla ollaan kuin lumiukko tuon kaukkarin suhteen  
Viritin on Hauppauge Nova-DVB-t USB  http://www.hauppauge.co.uk/site/products/data_novatstick.html
(Ei saman värisiä kuin linkissä, mutta sama tuotekoodi)

Koodia: [Valitse]

cat /proc/bus/input/devices

I: Bus=0003 Vendor=2040 Product=7070 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:02.1-3/ir0
S: Sysfs=/devices/pci0000:00/0000:00:02.1/usb1/1-3/input/input4
U: Uniq=
H: Handlers=kbd event4
B: EV=3
B: KEY=14afc336 294284f 0 0 0 4 80158000 2190 40000801 9e96c0 0 900240 10004ffc


Eli LIRC.n asetuksista ei löydy kakea&vastaanotinta.
Minkä valitsen Remote control configurationista:
(Pelkästään Hauppaugen)

Hauppauge DVB-s card (ver. 2.1)                                                                
Hauppauge HVR-1100                                                                            
Hauppauge HVR-1300                                                                            
Hauppauge Nova-T 500                                                                              
Hauppauge TV card  

Entäs tämä:
IR transmitter, if present:

None                                                                                                  
Custom                                                                                              
Command IR : Direct TV Receiver                                                                        
Command IR : Dish Receiver                                                                              
Command IR : Motorola Cable box                                                                        
Command IR : Pioneer Cable box                                                                          
Command IR : Scientific Atlanta Cable box                                                              
Command IR : Sky Satellite Receiver                                                                    
Microsoft Windows Media Center V2 (usb) : Direct TV Receiver                                            
Microsoft Windows Media Center V2 (usb) : Dish Receiver                                                
Microsoft Windows Media Center V2 (usb) : Motorola Cable box                                          
Microsoft Windows Media Center V2 (usb) : Pioneer Cable box                                            
Microsoft Windows Media Center V2 (usb) : Scientific Atlanta Cable box                                  
Microsoft Windows Media Center V2 (usb) : Sky Satellite Receiver                                      
Serial Port (UART) : Direct TV Receiver                                                            
Serial Port (UART) : Dish Receiver                                                                    
Serial Port (UART) : Motorola Cable box                                                            
Serial Port (UART) : Pioneer Cable box                                                              
Serial Port (UART) : Scientific Atlanta Cable box                                                
Serial Port (UART) : Sky Satellite Receiver                                                        
USB-UIRT2 : Direct TV Receiver                                                                        
USB-UIRT2 : Dish Receiver                                                                            
USB-UIRT2 : Motorola Cable box                                                                        
USB-UIRT2 : Pioneer Cable box                                                                          
USB-UIRT2 : Scientific Atlanta Cable box                                                              
USB-UIRT2 : Sky Satellite Receiver

[nm: jaoin aiheen VDR-keskustelusta]

[nm]

Eli LIRC.n asetuksista ei löydy kakea&vastaanotinta.
Minkä valitsen Remote control configurationista:

Kokeile vaihtoehtoa "Linux input layer (/dev/input/eventX)". Sama käy kaikkiin evdev-laitteina näkyviin vastaanottimiin.

Entäs tämä:
IR transmitter, if present:

Sinulla ei ole koneessa IR-lähetintä, etkä edes halua ohjata muita laitteita tietokoneen avulla, joten "None".

VDR:n tapauksessa remote-liitännäinen voisi kyllä olla helpompi ratkaisu kuin Lirc, mutta kokeile nyt sitä ensin kun aloitit. Myös Kaffeine on varmaankin mahdollista saada toimimaan Lircin kautta.

[runeh]

Huomenta nm  

Kokeilinkin tuota "Linux input layer (/dev/input/eventX)" vaihtoehtoa, mutta ei tapahdu mitään irw.llä eikä vdr.ssä.

Saan tälläisen virheen kylmä käynnistyksen jälkeen "rc submit urb failed"
Pikainen googlaaminen heitti ensimmäisiä hakuja viitaten kaukosäätimeen...


# /etc/lirc/hardware.conf
#
#Chosen Remote Control
REMOTE="Linux input layer (/dev/input/eventX)"
REMOTE_MODULES=""
REMOTE_DRIVER="devinput"
REMOTE_DEVICE="/dev/input/event4"
REMOTE_SOCKET=""
REMOTE_LIRCD_CONF="devinput/lircd.conf.devinput"
REMOTE_LIRCD_ARGS=""

#Chosen IR Transmitter
TRANSMITTER="None"
TRANSMITTER_MODULES=""
TRANSMITTER_DRIVER=""
TRANSMITTER_DEVICE=""
TRANSMITTER_SOCKET=""
TRANSMITTER_LIRCD_CONF=""
TRANSMITTER_LIRCD_ARGS=""

#Enable lircd
START_LIRCD="true"

#Don't start lircmd even if there seems to be a good config file
#START_LIRCMD="false"

#Try to load appropriate kernel modules
LOAD_MODULES="true"

# Default configuration files for your hardware if any
LIRCMD_CONF=""

#Forcing noninteractive reconfiguration
#If lirc is to be reconfigured by an external application
#that doesn't have a debconf frontend available, the noninteractive
#frontend can be invoked and set to parse REMOTE and TRANSMITTER
#It will then populate all other variables without any user input
#If you would like to configure lirc via standard methods, be sure
#to leave this set to "false"
FORCE_NONINTERACTIVE_RECONFIGURATION="false"
START_LIRCMD=""

# Remote settings required by gnome-lirc-properties
REMOTE_MODEL="DVB-T"
REMOTE_VENDOR="DVICO"

# Receiver settings required by gnome-lirc-properties
RECEIVER_MODEL="USB\ Remote"
RECEIVER_VENDOR="DViCO"

[nm]

Saan tälläisen virheen kylmä käynnistyksen jälkeen "rc submit urb failed"
Pikainen googlaaminen heitti ensimmäisiä hakuja viitaten kaukosäätimeen...

No tarjoilitko sitten lämmintä boottia? Sait kuitenkin kaukosäätimen jo jossain vaiheessa toimimaan, joten kyllä se on mahdollista saada pelaamaan myös Lircin kanssa.

Huomaa myös että kaukosäätimen laite voi vaihtua bootissa, eli /dev/input/event4:n sijaan se voi joskus olla vaikkapa /dev/input/event3. Suoran osoituksen sijaan voit käyttää /dev/input/by-id/... tai by-path-linkkejä tai tehdä kaukosäätimelle oman linkin udev-säännöllä.

Voit testata IR-vastaanottimen toimintaa lukemalla suoraan evdev-laitteita. Päätteessä: cat /dev/input/event4 (ja painele sitten kaukosäätimen nappeja). Lircin toimintaa voi testata irw:llä.

[runeh]

Juu ei.. Ei onnaa.

Mites oisko siihen remote liitännäiseen ohjetta?

[nm]

Juu ei.. Ei onnaa.

Mikä kohta? Yritä saada jotain ulos sieltä laitteelta cat-komennolla. Ajuripuoli on saatava ensin sellaiseen kuntoon, että vastaanotin antaa elonmerkkejä.

Sammuta Lirc, ettei se varaa laitteita itselleen (sudo service lirc stop).

[runeh]

Ei tuu mitään tuolla cat.llä
Poistan nyt LIRC.n ja voisin kokasta sitä remote-liitännäistä.. tuleepahan nää si testailtua 

[nm]

Ei tuu mitään tuolla cat.llä
Poistan nyt LIRC.n ja voisin kokasta sitä remote-liitännäistä.. tuleepahan nää si testailtua 

Testaa remote-liitännäistä vasta sitten kun saat evdevin toimimaan. Turhaa työtä muuten.

Eli jos ajuri herjasi IR:stä, käynnistä järjestelmä uudelleen tai ota tikku irti ja kytke takaisin. Tarkista sitten kernelin loki uudelleen ja kokeile laitteita. Muista myös tarkistaa event-laitteen numero, että osaat kokeilla oikeaa tiedostoa.

[runeh]

Poistin LIRC.n , käynnistin koneen, päätteessä cat /dev/input/event4
ei tullu ruudulle mitään kun painelin kakea.


cat /proc/bus/input/devices


I: Bus=0003 Vendor=2040 Product=7070 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:02.1-4/ir0
S: Sysfs=/devices/pci0000:00/0000:00:02.1/usb1/1-4/input/input4
U: Uniq=
H: Handlers=kbd event4
B: EV=3
B: KEY=14afc336 294284f 0 0 0 4 80158000 2190 40000801 9e96c0 0 900240 10004ffc

dmesg

[    7.281657] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
[    7.281913] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[    7.282270] DVB: registering new adapter (Hauppauge Nova-T Stick)
[    7.298685] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
[    7.298690]   alloc irq_desc for 20 on node -1
[    7.298692]   alloc kstat_irqs on node -1
[    7.298702] HDA Intel 0000:00:07.0: PCI INT B -> Link[LAZA] -> GSI 20 (level, low) -> IRQ 20
[    7.298705] hda_intel: Disable MSI for Nvidia chipset
[    7.298742] HDA Intel 0000:00:07.0: setting latency timer to 64
[    7.493031] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[    7.704039] DiB0070: successfully identified
[    7.704109] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:02.1/usb1/1-4/input/input4
[    7.704161] dvb-usb: schedule remote query interval to 50 msecs.
[    7.704164] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.
[    7.704532] dib0700: rc submit urb failed
[    7.704533]
[    7.704661] usbcore: registered new interface driver dvb_usb_dib0700
[    8.093031] hda_codec: ALC888: BIOS auto-probing.
[    8.112162] usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x04A9 pid 0x1734
[    8.112251] usbcore: registered new interface driver usblp
[   10.577473] EXT3-fs (sdb2): using internal journal
[   13.054217] type=1400 audit(1296829405.097:10): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=1155 comm="apparmor_parser"
[   13.054424] type=1400 audit(1296829405.097:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1155 comm="apparmor_parser"
[   13.054543] type=1400 audit(1296829405.097:12): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1155 comm="apparmor_parser"
[   13.220680] type=1400 audit(1296829405.261:13): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=1154 comm="apparmor_parser"
[   13.255872] type=1400 audit(1296829405.297:14): apparmor="STATUS" operation="profile_load" name="/usr/bin/freshclam" pid=1169 comm="apparmor_parser"
[   13.371122] type=1400 audit(1296829405.417:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1170 comm="apparmor_parser"
[   13.371139] type=1400 audit(1296829405.417:16): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1162 comm="apparmor_parser"
[   13.371405] type=1400 audit(1296829405.417:17): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1170 comm="apparmor_parser"
[   13.371423] type=1400 audit(1296829405.417:18): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1162 comm="apparmor_parser"
[   13.439920] type=1400 audit(1296829405.485:19): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1156 comm="apparmor_parser"
[   14.841063] r8169 0000:03:00.0: eth0: link down
[   14.841233] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.821029] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   16.821032] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hardware performance
[   16.821034] vboxdrv: counter framework which can generate NMIs is active. You have to prevent
[   16.821035] vboxdrv: the usage of hardware performance counters by
[   16.821036] vboxdrv:   echo 2 > /proc/sys/kernel/perf_counter_paranoid
[   16.821038] vboxdrv: Found 2 processor cores.
[   16.821251] vboxdrv: fAsync=1 offMin=0xb5f offMax=0xb5f
[   16.822019] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is 'normal'.
[   16.822022] vboxdrv: Successfully loaded version 3.2.10 (interface 0x00140001).
[   17.847593] usb 1-2: usbfs: interface 1 claimed by usblp while 'usb' sets config #1
[   44.512069] ISO 9660 Extensions: Microsoft Joliet Level 1
[   44.550564] ISOFS: changing to secondary root
[   62.944494] Netfilter messages via NETLINK v0.30.
[   93.954281] CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
[   94.644024] Clocksource tsc unstable (delta = -339111940 ns)
[  217.453286] lo: Disabled Privacy Extensions


(remote-plugin on nyt asennettu)

[nm]

dib0700: rc submit urb failed

Tuosta virheestä pitäisi päästä eroon. Kokeile ensin vaikkapa vanhemmalla firmwarella, eli siirrä tiedosto /lib/firmware/dvb-usb-dib0700-1.20.fw muualle ja tee symbolinen linkki vanhempaan versioon. Onnistuu komennoilla:

Koodia: [Valitse]

sudo mv /lib/firmware/dvb-usb-dib0700-1.20.fw /
sudo ln -s /lib/firmware/dvb-usb-dib0700-1.10.fw /lib/firmware/dvb-usb-dib0700-1.20.fw
Sammuta sitten VDR (sudo service vdr stop), ota tikku irti, laita takaisin ja tarkista dmesg. Latautuuko firmware ja tuleeko sama virhe edelleen?

Jos tästä ei ollut apua, siirrä uudempi firmware takaisin:

Koodia: [Valitse]

sudo mv /dvb-usb-dib0700-1.20.fw /lib/firmware/
Kokeile sitten uudempia ajureita. Paketin saa yaVDR:n PPA:sta. Tässä suora linkki, jos et käytä samasta paikasta ladattua VDR:ää: https://launchpad.net/~yavdr/+archive/stable-vdr/+files/v4l-dvb-dkms_0%7E20101018.15139_all.deb

[runeh]

Tein tähän saakka:
Koodia:
sudo mv /lib/firmware/dvb-usb-dib0700-1.20.fw /
sudo ln -s /lib/firmware/dvb-usb-dib0700-1.10.fw /lib/firmware/dvb-usb-dib0700-1.20.fw

Sammuta sitten VDR (sudo service vdr stop), ota tikku irti, laita takaisin ja tarkista dmesg. Latautuuko firmware ja tuleeko sama virhe edelleen?


Virhe hävisi, mutta firmware ei lataannu.  dmesg


[   23.453969] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
[   23.454517] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[   23.455756] type=1400 audit(1296832202.416:9): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/ntpd" pid=655 comm="apparmor_parser"
[   23.456180] DVB: registering new adapter (Hauppauge Nova-T Stick)
[   23.458623] ip_tables: (C) 2000-2006 Netfilter Core Team
[   23.459604] nvidia: module license 'NVIDIA' taints kernel.
[   23.459608] Disabling lock debugging due to kernel taint
[   23.533505] HDA Intel 0000:00:07.0: PCI->APIC IRQ transform: INT B -> IRQ 34
[   23.533509] hda_intel: Disable MSI for Nvidia chipset
[   23.533561] HDA Intel 0000:00:07.0: setting latency timer to 64
[   23.565025] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   23.566336] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[   23.566339] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[   23.566341] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[   23.595944] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   23.699071] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[   23.916334] DiB0070: successfully identified
[   23.916334] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:02.1/usb1/1-4/input/input2
[   23.916334] dvb-usb: schedule remote query interval to 50 msecs.
[   23.916334] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.
[   23.916635] usbcore: registered new interface driver dvb_usb_dib0700
[   24.160005] hda_codec: ALC888: BIOS auto-probing.
[   24.546920] nvidia 0000:04:00.0: PCI->APIC IRQ transform: INT A -> IRQ 34
[   24.546920] nvidia 0000:04:00.0: setting latency timer to 64
[   24.546920] vgaarb: device changed decodes: PCI:0000:04:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   24.548106] NVRM: loading NVIDIA UNIX x86 Kernel Module  270.18  Tue Jan 18 21:44:45 PST 2011
[   24.692751] EXT3-fs (sdb2): using internal journal
[   26.170615] type=1400 audit(1296832205.132:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1082 comm="apparmor_parser"
[   26.170891] type=1400 audit(1296832205.132:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1082 comm="apparmor_parser"
[   26.198621] r8169 0000:03:00.0: eth0: link down
[   26.198778] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.201283] ppdev: user-space parallel port driver
[   26.206733] parport_pc 00:07: reported by Plug and Play BIOS
[   26.206776] parport0: PC-style at 0x378, irq 7 [PCSPP]
[   26.300146] lp0: using parport0 (interrupt-driven).
[   26.347526] NVRM: failed to register with the ACPI subsystem!
[   26.653060] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   26.653063] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hardware performance
[   26.653064] vboxdrv: counter framework which can generate NMIs is active. You have to prevent
[   26.653065] vboxdrv: the usage of hardware performance counters by
[   26.653066] vboxdrv:   echo 2 > /proc/sys/kernel/perf_counter_paranoid
[   26.653068] vboxdrv: Found 2 processor cores.
[   26.654018] vboxdrv: fAsync=1 offMin=0x14c29 offMax=0x14c29
[   26.654757] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is 'normal'.
[   26.654759] vboxdrv: Successfully loaded version 3.2.10 (interface 0x00140001).
[   27.850199] usb 1-2: usbfs: interface 1 claimed by usblp while 'usb' sets config #1
[   30.688757] ISO 9660 Extensions: Microsoft Joliet Level 1
[   30.719222] ISOFS: changing to secondary root
[   37.428681] NVRM: failed to unregister from the ACPI subsystem!
[   37.489237] NVRM: failed to register with the ACPI subsystem!
[   51.541351] Netfilter messages via NETLINK v0.30.

(Pääsin tästä eroon "Clocksource tsc unstable (delta = -339111940 ns" laittamalla BIOS.sta ACPI.n Disabled)

Siirrän uudemman firen takaisin ja kokeilen noita uusia v4l ajureita.

[nm]

Virhe hävisi, mutta firmware ei lataannu.

Firmwarea ei ladata silloin kun tikku on lämpimässä tilassa: found a 'Hauppauge Nova-T Stick' in warm state

Tikun pitäisi olla varmaan kauemmin virratta.

Mutta olisit kokeillut IR:ää nyt kun virhettä ei tullut.

[runeh]

Oh nou   

Laitoin uudet firet takas--> virhe palasi...
No laitan ne vanhat back ja siis miten nyt kokeilen IR.ää?

Nyt on muuten event2

I: Bus=0003 Vendor=2040 Product=7070 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:02.1-4/ir0
S: Sysfs=/devices/pci0000:00/0000:00:02.1/usb1/1-4/input/input2
U: Uniq=
H: Handlers=kbd event2
B: EV=3
B: KEY=14afc336 294284f 0 0 0 4 80158000 2190 40000801 9e96c0 0 900240 10004ffc

[nm]

No laitan ne vanhat back ja siis miten nyt kokeilen IR.ää?

Nyt on muuten event2

cat /dev/input/event2

[runeh]

Okey nyt tapahtuu! Mutta cat.llä heitti lupa evätty, ajoin sudolla (ruudulla ei näy mitään kakea painellessa)   dmesg

[  645.191439] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
[  645.391278] dib0700: firmware started successfully.
[  645.895278] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
[  645.895329] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  645.895334] DVB: registering new adapter (Hauppauge Nova-T Stick)
[  646.111235] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[  646.327218] DiB0070: successfully identified
[  646.327287] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:02.1/usb1/1-4/input/input3
[  646.331324] dvb-usb: schedule remote query interval to 50 msecs.
[  646.331327] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.

[  646.331327] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.
[  665.757970] [UFW BLOCK] IN=ppp0 OUT= MAC= SRC=94.137.254.38 DST=85.78.216.209 LEN=131 TOS=0x00 PREC=0x00 TTL=113 ID=11150 PROTO=UDP SPT=61899 DPT=37979 LEN=111 MARK=0x14
[  730.825687] [UFW BLOCK] IN=ppp0 OUT= MAC= SRC=95.78.17.92 DST=85.78.216.209 LEN=131 TOS=0x00 PREC=0x00 TTL=245 ID=59731 PROTO=UDP SPT=37564 DPT=37979 LEN=111 MARK=0x14
[  742.744906] [UFW BLOCK] IN=ppp0 OUT= MAC= SRC=118.243.87.232 DST=85.78.216.209 LEN=131 TOS=0x00 PREC=0x00 TTL=114 ID=14066 PROTO=UDP SPT=18253 DPT=37979 LEN=111 MARK=0x14
[  762.179600] dib0700: Unknown remote controller key: 1C  5  1  0
[  762.283593] dib0700: Unknown remote controller key: 1C  5  1  0
[  762.387586] dib0700: Unknown remote controller key: 1C  5  1  0
[  762.751563] dib0700: Unknown remote controller key: 1C  6  0  0
[  762.855557] dib0700: Unknown remote controller key: 1C  6  0  0
[  762.959548] dib0700: Unknown remote controller key: 1C  6  0  0
[  763.271528] dib0700: Unknown remote controller key: 1C 12  1  0
[  763.427605] dib0700: Unknown remote controller key: 1C 12  1  0
[  763.531514] dib0700: Unknown remote controller key: 1C 12  1  0
[  763.739497] dib0700: Unknown remote controller key: 1C  6  0  0
[  763.843490] dib0700: Unknown remote controller key: 1C  6  0  0
[  763.947483] dib0700: Unknown remote controller key: 1C  6  0  0
[  764.207467] dib0700: Unknown remote controller key: 1C  5  1  0
[  764.311459] dib0700: Unknown remote controller key: 1C  5  1  0
[  765.351391] dib0700: Unknown remote controller key: 1C 20  0  0
[  765.455384] dib0700: Unknown remote controller key: 1C 20  0  0
[  765.559380] dib0700: Unknown remote controller key: 1C 20  0  0
[  765.975350] dib0700: Unknown remote controller key: 1C 21  1  0
[  766.079343] dib0700: Unknown remote controller key: 1C 21  1  0
[  766.183336] dib0700: Unknown remote controller key: 1C 21  1  0
[  767.171272] dib0700: Unknown remote controller key: 1C 11  0  0
[  767.275264] dib0700: Unknown remote controller key: 1C 11  0  0
[  767.379257] dib0700: Unknown remote controller key: 1C 11  0  0
[  767.587245] dib0700: Unknown remote controller key: 1C 10  1  0
[  767.691238] dib0700: Unknown remote controller key: 1C 10  1  0
[  767.795230] dib0700: Unknown remote controller key: 1C 10  1  0
[  768.783165] dib0700: Unknown remote controller key: 1C 14  0  0
[  768.887160] dib0700: Unknown remote controller key: 1C 14  0  0
[  768.991151] dib0700: Unknown remote controller key: 1C 14  0  0
[  769.563116] dib0700: Unknown remote controller key: 1C 15  1  0
[  769.667107] dib0700: Unknown remote controller key: 1C 15  1  0
[  769.771100] dib0700: Unknown remote controller key: 1C 15  1  0
[  770.135076] dib0700: Unknown remote controller key: 1C 17  0  0
[  770.239069] dib0700: Unknown remote controller key: 1C 17  0  0
[  771.330998] dib0700: Unknown remote controller key: 1C  8  1  0
[  771.434990] dib0700: Unknown remote controller key: 1C  8  1  0
[  771.538983] dib0700: Unknown remote controller key: 1C  8  1  0
[  771.694973] dib0700: Unknown remote controller key: 1C  5  0  0
[  771.798966] dib0700: Unknown remote controller key: 1C  5  0  0
[  772.006944] dib0700: Unknown remote controller key: 1C  4  1  0
[  772.162943] dib0700: Unknown remote controller key: 1C  4  1  0
[  772.370929] dib0700: Unknown remote controller key: 1C  7  0  0
[  815.356151] [UFW BLOCK] IN=ppp0 OUT= MAC= SRC=83.93.23.240 DST=85.78.216.209 LEN=90 TOS=0x00 PREC=0x00 TTL=118 ID=25889 PROTO=UDP SPT=12375 DPT=37979 LEN=70 MARK=0x14



Mitäs nyt?

[nm]

Mitäs nyt?

Ajuri ei tunnista kaukosäätimen koodeja, eli ajuriversio on luultavasti liian vanha. Kokeile seuraavaksi sitä yaVDR:n pakettia.

[runeh]

Ehin jo asentaa sen v4l.n

[nm]

Ehin jo asentaa sen v4l.n

Käynnistitkö koneen uudelleen?

[runeh]

en      reboot!!

[runeh]

Ei vaikutusta... cat /dev/input/event2 ei herjannu enää "lupa evätty" mutta siis ruudulla ei mitään kun painelee kaken nappuloita.