Mitä viestejä? [Ratkaistu]

[Ben]

Mitä nämä viestit tarkoittavat, kun usb-liittimissä ei ole mitään?

pena@pena-laptop:~$ lsusb
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
pena@pena-laptop:~$

Ben

[Ben]

Entäs tämä sitten?

pena@pena-laptop:~$ lsusb
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
pena@pena-laptop:~$

Lisäsin usb-kortin ylimääräiseen korttipaikkaan.

Ben

[qwertyy]

Ihan normaalia, kone on tunnistanut tuon lisäämäsi kortin ja siinä on veikaten 4 paikkaa.
Pätkä oman HP:n vastaavasta

lsusb
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 004: ID 0421:0154 Nokia Mobile Phones
Bus 005 Device 003: ID 046d:09b8 Logitech, Inc.
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module]
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 046d:c041 Logitech, Inc.
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Tuossa nyt näkyy vain hiiri, nokian puhelin ja wlan/bt kilkkeet samassa. Root hub on vapaasti käännettynä keskitin

[Rottis]

Ja rautalangasta väännettynä USB-liitäntöjä (saattaa olla useampia yhden rivin takana)

[Ben]

Kun kone kerran tunnistaa USB:t, niin miksi langaton hiiri ei toimi?

Ben

[gdm]

Kun kone kerran tunnistaa USB:t, niin miksi langaton hiiri ei toimi?

Ben

Antamissasi tulosteissa ei ollut mitään mainintaa liitetyistä lisälaitteista.

Irroita hiiri, laita takaisin sisään ja seuraavan tuloste dmesg |tail -20 && lsusb

Usb-laitteiden tunnisteet voi päivittää komennolla sudo update-usbids

Jos ongelmasi koskee pelkästään tuota langattoman hiiren toimintaa, niin voitko muokata otsikkoa kuvaavammaksi?
Nykyisellään ei kuvaa juuri mitään..

[Ben]

Komento: dmesg

Tulos:

 Seuraavat virheet tapahtuivat lähetettäessä viestiä:
Viestissä on liikaa merkkejä. Suurin sallittu määrä on (20000).

 0.958751] pci 0000:00:1e.0:   IO window: 0x4000-0x9fff
[    0.958759] pci 0000:00:1e.0:   MEM window: 0xd0200000-0xdfffffff
[    0.958766] pci 0000:00:1e.0:   PREFETCH window: 0x000000f0000000-0x000000f7ffffff
[    0.958793] pci 0000:00:1e.0: setting latency timer to 64
[    0.959504] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[    0.959509] PCI: setting IRQ 11 as level-triggered
[    0.959515] pci 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[    0.960147] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[    0.960153] pci 0000:02:00.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[    0.960775] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[    0.960781] pci 0000:09:02.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    0.960798] pci 0000:09:02.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    0.960808] bus: 00 index 0 io port: [0, ffff]
[    0.960813] bus: 00 index 1 mmio: [0, ffffffff]
[    0.960817] bus: 01 index 0 io port: [3000, 3fff]
[    0.960821] bus: 01 index 1 mmio: [d0100000, d01fffff]
[    0.960825] bus: 01 index 2 mmio: [e8000000, efffffff]
[    0.960828] bus: 01 index 3 mmio: [0, 0]
[    0.960831] bus: 02 index 0 io port: [4000, 9fff]
[    0.960835] bus: 02 index 1 mmio: [d0200000, dfffffff]
[    0.960839] bus: 02 index 2 mmio: [f0000000, f7ffffff]
[    0.960842] bus: 02 index 3 io port: [0, ffff]
[    0.960845] bus: 02 index 4 mmio: [0, ffffffff]
[    0.960849] bus: 10 index 0 io port: [5000, 50ff]
[    0.960852] bus: 10 index 1 io port: [5400, 54ff]
[    0.960855] bus: 10 index 2 mmio: [f0000000, f3ffffff]
[    0.960858] bus: 10 index 3 mmio: [d4000000, d7ffffff]
[    0.960862] bus: 14 index 0 io port: [5800, 58ff]
[    0.960865] bus: 14 index 1 io port: [5c00, 5cff]
[    0.960868] bus: 14 index 2 mmio: [f4000000, f7ffffff]
[    0.960871] bus: 14 index 3 mmio: [d8000000, dbffffff]
[    0.960875] bus: 09 index 0 io port: [4000, 4fff]
[    0.960878] bus: 09 index 1 mmio: [44000000, 4bffffff]
[    0.960881] bus: 09 index 2 mmio: [54000000, 5bffffff]
[    0.960885] bus: 09 index 3 io port: [4000, 9fff]
[    0.960888] bus: 09 index 4 mmio: [d0200000, dfffffff]
[    0.960891] bus: 09 index 5 mmio: [f0000000, f7ffffff]
[    0.960894] bus: 09 index 6 io port: [0, ffff]
[    0.960897] bus: 09 index 7 mmio: [0, ffffffff]
[    0.960901] bus: 0a index 0 io port: [4000, 40ff]
[    0.960904] bus: 0a index 1 io port: [4400, 44ff]
[    0.960907] bus: 0a index 2 mmio: [54000000, 57ffffff]
[    0.960910] bus: 0a index 3 mmio: [44000000, 47ffffff]
[    0.960914] bus: 0e index 0 io port: [4800, 48ff]
[    0.960917] bus: 0e index 1 io port: [4c00, 4cff]
[    0.960920] bus: 0e index 2 mmio: [58000000, 5bffffff]
[    0.960924] bus: 0e index 3 mmio: [48000000, 4bffffff]
[    0.960946] NET: Registered protocol family 2
[    0.961215] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.961767] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.963192] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.964196] TCP: Hash tables configured (established 131072 bind 65536)
[    0.964207] TCP reno registered
[    0.964459] NET: Registered protocol family 1
[    0.964690] checking if image is initramfs... it is
[    1.460088] Switched to high resolution mode on CPU 0
[    1.947334] Freeing initrd memory: 8007k freed
[    1.947682] Simple Boot Flag at 0x35 set to 0x1
[    1.948480] audit: initializing netlink socket (disabled)
[    1.948513] type=2000 audit(1229851563.948:1): initialized
[    1.955590] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.959594] VFS: Disk quotas dquot_6.5.1
[    1.959764] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.959957] msgmni has been set to 1509
[    1.960740] io scheduler noop registered
[    1.960747] io scheduler anticipatory registered
[    1.960753] io scheduler deadline registered
[    1.960790] io scheduler cfq registered (default)
[    1.960872] pci 0000:01:00.0: Boot video device
[    1.960904] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[    1.961565] isapnp: Scanning for PnP cards...
[    2.315322] isapnp: No Plug & Play device found
[    2.395542] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    2.397578] serial 00:09: activated
[    2.398107] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
[    2.398472] serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[    2.398485] serial 0000:00:1f.6: PCI INT B disabled
[    2.401533] brd: module loaded
[    2.401664] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    2.401901] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[    2.406280] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.406293] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.407059] mice: PS/2 mouse device common for all mice
[    2.407357] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    2.407381] rtc0: alarms up to one month, y3k
[    2.407627] EISA: Probing bus 0 at eisa.0
[    2.407639] Cannot allocate resource for EISA slot 1
[    2.407645] Cannot allocate resource for EISA slot 2
[    2.407650] Cannot allocate resource for EISA slot 3
[    2.407655] Cannot allocate resource for EISA slot 4
[    2.407660] Cannot allocate resource for EISA slot 5
[    2.407665] Cannot allocate resource for EISA slot 6
[    2.407687] Cannot allocate resource for EISA slot 7
[    2.407692] Cannot allocate resource for EISA slot 8
[    2.407697] EISA: Detected 0 cards.
[    2.407705] cpuidle: using governor ladder
[    2.407710] cpuidle: using governor menu
[    2.408673] TCP cubic registered
[    2.408725] Using IPI No-Shortcut mode
[    2.409253] registered taskstats version 1
[    2.409475]   Magic number: 4:941:424
[    2.409685] rtc_cmos 00:06: setting system clock to 2008-12-21 09:26:05 UTC (1229851565)
[    2.409691] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.409696] EDD information not available.
[    2.410386] Freeing unused kernel memory: 424k freed
[    2.410465] Write protecting the kernel text: 2576k
[    2.410511] Write protecting the kernel read-only data: 936k
[    2.414948] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    2.732673] fuse init (API version 7.9)
[    2.982341] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    2.987417] processor ACPI0007:00: registered as cooling_device0
[    2.987425] ACPI: Processor [CPU] (supports 8 throttling states)
[    3.018225] thermal LNXTHERM:01: registered as thermal_zone0
[    3.019911] ACPI: Thermal Zone [THM0] (51 C)
[    4.079737] ACPI: ACPI Dock Station Driver
[    4.331085] usbcore: registered new interface driver usbfs
[    4.331133] usbcore: registered new interface driver hub
[    4.346239] usbcore: registered new device driver usb
[    4.436421] SCSI subsystem initialized
[    4.436569] USB Universal Host Controller Interface driver v3.0
[    4.437251] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[    4.437268] uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[    4.437282] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    4.437288] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    4.437396] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    4.437430] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
[    4.437705] usb usb1: configuration #1 chosen from 1 choice
[    4.437752] hub 1-0:1.0: USB hub found
[    4.437768] hub 1-0:1.0: 2 ports detected
[    4.454179] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[    4.454184] e100: Copyright(c) 1999-2006 Intel Corporation
[    4.574408] libata version 3.00 loaded.
[    4.645140] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[    4.645790] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[    4.645796] uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[    4.645810] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    4.645816] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    4.645880] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    4.645913] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
[    4.646131] usb usb2: configuration #1 chosen from 1 choice
[    4.646179] hub 2-0:1.0: USB hub found
[    4.646193] hub 2-0:1.0: 2 ports detected
[    4.748534] uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    4.748554] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    4.748559] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    4.748607] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    4.748644] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
[    4.748833] usb usb3: configuration #1 chosen from 1 choice
[    4.748883] hub 3-0:1.0: USB hub found
[    4.748901] hub 3-0:1.0: 2 ports detected
[    4.756089] usb 1-1: new full speed USB device using uhci_hcd and address 2
[    4.852640] ata_piix 0000:00:1f.1: version 2.12
[    4.852659] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[    4.852672] ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    4.852750] ata_piix 0000:00:1f.1: setting latency timer to 64
[    4.857181] scsi0 : ata_piix
[    4.857390] scsi1 : ata_piix
[    4.859199] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14
[    4.859204] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15
[    4.876073] usb 1-1: device descriptor read/64, error -71
[    5.025327] ata1.00: ATA-6: ST94813A, 3.04, max UDMA/100
[    5.025334] ata1.00: 78140160 sectors, multi 16: LBA48
[    5.043783] ata1.00: configured for UDMA/100
[    5.100076] usb 1-1: device descriptor read/64, error -71
[    5.204437] ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4160N, 0012, max UDMA/33
[    5.220357] ata2.00: configured for UDMA/33
[    5.220593] scsi 0:0:0:0: Direct-Access     ATA      ST94813A         3.04 PQ: 0 ANSI: 5
[    5.316091] usb 1-1: new full speed USB device using uhci_hcd and address 3
[    5.336433] scsi 1:0:0:0: CD-ROM            HL-DT-ST RW/DVD GCC-4160N 0012 PQ: 0 ANSI: 5
[    5.338806] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[    5.338815] e100 0000:02:08.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
[    5.362425] e100 0000:02:08.0: PME# disabled
[    5.373579] e100: eth0: e100_probe: addr 0xd0200000, irq 11, MAC addr 00:09:6b:86:e7:e3
[    5.373697] pata_cmd64x 0000:09:01.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[    5.373912] scsi2 : pata_cmd64x
[    5.374038] scsi3 : pata_cmd64x
[    5.374402] ata3: PATA max UDMA/66 cmd 0x9020 ctl 0x9014 bmdma 0x9000 irq 11
[    5.374407] ata4: PATA max UDMA/66 cmd 0x9018 ctl 0x9010 bmdma 0x9008 irq 11
[    5.374448] pata_cmd64x: active 10 recovery 10 setup 3.
[    5.374458] pata_cmd64x: active 10 recovery 10 setup 3.
[    5.440087] usb 1-1: device descriptor read/64, error -71
[    5.540158] pata_cmd64x: active 10 recovery 10 setup 3.
[    5.540170] pata_cmd64x: active 10 recovery 10 setup 3.
[    5.664065] usb 1-1: device descriptor read/64, error -71
[    5.880115] usb 1-1: new full speed USB device using uhci_hcd and address 4
[    6.288090] usb 1-1: device not accepting address 4, error -71
[    6.400086] usb 1-1: new full speed USB device using uhci_hcd and address 5
[    6.808060] usb 1-1: device not accepting address 5, error -71
[    6.808094] hub 1-0:1.0: unable to enumerate USB device on port 1
[    8.110214] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[    8.110281] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[    8.161896] Driver 'sd' needs updating - please use bus_type methods
[    8.165435] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[    8.165472] sd 0:0:0:0: [sda] Write Protect is off
[    8.165477] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

Terveisin

Ben

[Ben]

Poistin noin puolet merkeistä tuosta äskeisestä, jolloin meni läpi.

Ben

[Ben]

Sitten vielä tämä:

pena@pena-laptop:~$ -20&&lsusb
bash: -20: command not found
pena@pena-laptop:~$ -20 && lsusb
bash: -20: command not found
pena@pena-laptop:~$ sudo update-usb
[sudo] password for pena:
sudo: update-usb: command not found
pena@pena-laptop:~$

Ben

[Lasse.]

Sitten vielä tämä:

pena@pena-laptop:~$ -20&&lsusb
bash: -20: command not found
pena@pena-laptop:~$ -20 && lsusb
bash: -20: command not found
pena@pena-laptop:~$ sudo update-usb
[sudo] password for pena:
sudo: update-usb: command not found
pena@pena-laptop:~$

Ben

Siis, tarkoitus oli laittaa koko pötkö kerralla "dmesg |tail -20 && lsusb", ei erikseen.

[Ben]

Taisi mennä vieläkin väärin. Kone vastasi:

pena@pena-laptop:~$ dmesg|tail-20&&lsusb
bash: tail-20: command not found
pena@pena-laptop:~$

Ben

[Kullervo]

Taisi mennä vieläkin väärin. Kone vastasi:

pena@pena-laptop:~$ dmesg|tail-20&&lsusb
bash: tail-20: command not found
pena@pena-laptop:~$

Ben

Välilyönti!

[masa]

Copy-pastea tuo komento niin e tule typoja 

[Ben]

Nyt näyttää tältä:

pena@pena-laptop:~$ dmesg|tail -20 && lsusb
[   36.537296] [drm] Initialized drm 1.1.0 20060810
[   36.550484] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[   36.811359] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[   36.811407] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[   36.811438] pci 0000:01:00.0: putting AGP V2 device into 4x mode
[   37.035881] [drm] Setting GART location based on new memory map
[   37.035904] [drm] Loading R100 Microcode
[   37.035962] [drm] writeback test succeeded in 1 usecs
[  138.676464] ppdev0: registered pardevice
[  138.724587] ppdev0: unregistered pardevice
[  139.765957] ppdev0: registered pardevice
[  139.812086] ppdev0: unregistered pardevice
[  141.076512] ppdev0: registered pardevice
[  141.124420] ppdev0: unregistered pardevice
[  520.224106] usb 2-2: USB disconnect, address 2
[ 1355.000155] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 1355.201060] NET: Registered protocol family 17
[ 1371.498882] NET: Registered protocol family 10
[ 1371.500825] lo: Disabled Privacy Extensions
[ 1382.392057] eth0: no IPv6 routers present
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Ben
Bus 002 Device 003: ID 046d:c51b Logitech, Inc.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
pena@pena-laptop:~$

[Ben]

Ai niin, telakka on irti, silloin langaton toimii niin kuin olen jo aiemmin kertonut.

Hiiri on tuo Logitech

Ben

[Ben]

Tämä tulee, kun telakka on kytkettynä:

pena@pena-laptop:~$ dmesg|tail -20 && lsusb
[   33.646120] Bluetooth: SCO socket layer initialized
[   33.690222] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   33.690238] Bluetooth: BNEP filters: protocol multicast
[   33.741168] Bluetooth: RFCOMM socket layer initialized
[   33.741824] Bluetooth: RFCOMM TTY layer initialized
[   33.741842] Bluetooth: RFCOMM ver 1.10
[   33.785194] Bridge firewalling registered
[   33.787585] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[   36.979282] pci 0000:01:00.0: power state changed by ACPI to D0
[   36.982079] pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[   37.392982] [drm] Initialized drm 1.1.0 20060810
[   37.408961] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[   37.658217] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[   37.658265] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[   37.658297] pci 0000:01:00.0: putting AGP V2 device into 4x mode
[   37.883725] [drm] Setting GART location based on new memory map
[   37.883747] [drm] Loading R100 Microcode
[   37.883805] [drm] writeback test succeeded in 1 usecs
[   37.916161] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[   38.195085] NET: Registered protocol family 17
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
pena@pena-laptop:~$

Ben

[jp1]

Kokeilin mielenkiinnosta IBM porttitoistimella jossa on 4 USB paikkaa niiden toimintaa. Testasin USB -tikulla ja totesin etteivät porttitoistimen USB:t toimineet.
Tämä vain tiedoksenne, koska se ei ole minulle ongelma, käytän porttitoistimessa langallista hiirtä ja läppärin USB -portit toimivat kuten pitääkin.

Hieman lisätietoa:
ThinkPad Dock II - Overview

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-46393

Supported operating systems

The ThinkPad Dock II supports the same operating system as the ThinkPad notebook system. The ThinkPad Dock II does not support Windows 95 or Linux operating systems.

USB 2.0 is not supported on Microsoft Windows 95, Windows 98, Windows Me or Windows NT. USB 1.1 is not supported on Windows 95 or Windows NT(*).

(*) Limited support provided for USB keyboard and mouse only by using customized driver.

[Ben]

Langaton hiiri ei siis ole tuettu telakassa eikä näin ollen toimi siinä.

Ben