Ikivanha Umax Astra 1220S-skanneri toimimaan? (Ratkaistu)

[Tepi]

Eli, meillä on tälläinen ikivanha skanneri minun huoneessani. Nyt kun veli on lukiossa ja minä yläasteella, on viime aikoina tullut aika paljon skannailtavaa, varsinkin kun takuukuitit skannataan myös. Ongelmana on se, että Ubuntu ei tunnista skanneria, vaan skanneri toimii ainostastaan Xp:llä.
Löytyisikö mistään ajureita tuolle vanhalle, raksuttavalle skannerille? En aina viitsisi uudelleenkäynnistellä konetta ja skannailla Xp:llä.

[Thinkit]

http://www.soslug.org/astra1200s
Kokeileppas jos tuolla toimisi.

T: Antti Nykänen

[Tuxer]

Pitäisi toimia:
http://www.sane-project.org/cgi-bin/driver.pl?manu=umax&model=astra+1220S&bus=scsi&v=&p=

EDIT: höp, sanoitkin tuossa ettei tunnista skanneria. Kokeile mita sanoo:

Koodia: [Valitse]

sane-find-scanner -v

[Tepi]

EDIT: höp, sanoitkin tuossa ettei tunnista skanneria. Kokeile mita sanoo:

Koodia: [Valitse]

sane-find-scanner -v

Sanoo tälläistä:
This is sane-find-scanner from sane-backends 1.0.19

  # sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

searching for SCSI scanners:
checking /dev/scanner... failed to open (Invalid argument)
checking /dev/sg0... open ok
found SCSI scanner "UMAX Astra 1220S V1.2" at /dev/sg0
checking /dev/sg1... failed to open (Invalid argument)
checking /dev/sg2... failed to open (Invalid argument)
checking /dev/sg3... failed to open (Invalid argument)
checking /dev/sg4... failed to open (Invalid argument)
checking /dev/sg5... failed to open (Invalid argument)
checking /dev/sg6... failed to open (Invalid argument)
checking /dev/sg7... failed to open (Invalid argument)
checking /dev/sg8... failed to open (Invalid argument)
checking /dev/sg9... failed to open (Invalid argument)
checking /dev/sga... failed to open (Invalid argument)
checking /dev/sgb... failed to open (Invalid argument)
checking /dev/sgc... failed to open (Invalid argument)
checking /dev/sgd... failed to open (Invalid argument)
checking /dev/sge... failed to open (Invalid argument)
checking /dev/sgf... failed to open (Invalid argument)
checking /dev/sgg... failed to open (Invalid argument)
checking /dev/sgh... failed to open (Invalid argument)
checking /dev/sgi... failed to open (Invalid argument)
checking /dev/sgj... failed to open (Invalid argument)
checking /dev/sgk... failed to open (Invalid argument)
checking /dev/sgl... failed to open (Invalid argument)
checking /dev/sgm... failed to open (Invalid argument)
checking /dev/sgn... failed to open (Invalid argument)
checking /dev/sgo... failed to open (Invalid argument)
checking /dev/sgp... failed to open (Invalid argument)
checking /dev/sgq... failed to open (Invalid argument)
checking /dev/sgr... failed to open (Invalid argument)
checking /dev/sgs... failed to open (Invalid argument)
checking /dev/sgt... failed to open (Invalid argument)
checking /dev/sgu... failed to open (Invalid argument)
checking /dev/sgv... failed to open (Invalid argument)
checking /dev/sgw... failed to open (Invalid argument)
checking /dev/sgx... failed to open (Invalid argument)
checking /dev/sgy... failed to open (Invalid argument)
checking /dev/sgz... failed to open (Invalid argument)
  # Your SCSI scanner was detected. It may or may not be supported by SANE. Try
  # scanimage -L and read the backend's manpage.

searching for USB scanners:
checking /dev/usb/scanner... failed to open (Invalid argument)
checking /dev/usb/scanner0... failed to open (Invalid argument)
checking /dev/usb/scanner1... failed to open (Invalid argument)
checking /dev/usb/scanner2... failed to open (Invalid argument)
checking /dev/usb/scanner3... failed to open (Invalid argument)
checking /dev/usb/scanner4... failed to open (Invalid argument)
checking /dev/usb/scanner5... failed to open (Invalid argument)
checking /dev/usb/scanner5... failed to open (Invalid argument)
checking /dev/usb/scanner7... failed to open (Invalid argument)
checking /dev/usb/scanner8... failed to open (Invalid argument)
checking /dev/usb/scanner9... failed to open (Invalid argument)
checking /dev/usb/scanner10... failed to open (Invalid argument)
checking /dev/usb/scanner11... failed to open (Invalid argument)
checking /dev/usb/scanner12... failed to open (Invalid argument)
checking /dev/usb/scanner13... failed to open (Invalid argument)
checking /dev/usb/scanner14... failed to open (Invalid argument)
checking /dev/usb/scanner15... failed to open (Invalid argument)
checking /dev/usbscanner... failed to open (Invalid argument)
checking /dev/usbscanner0... failed to open (Invalid argument)
checking /dev/usbscanner1... failed to open (Invalid argument)
checking /dev/usbscanner2... failed to open (Invalid argument)
checking /dev/usbscanner3... failed to open (Invalid argument)
checking /dev/usbscanner4... failed to open (Invalid argument)
checking /dev/usbscanner5... failed to open (Invalid argument)
checking /dev/usbscanner6... failed to open (Invalid argument)
checking /dev/usbscanner7... failed to open (Invalid argument)
checking /dev/usbscanner8... failed to open (Invalid argument)
checking /dev/usbscanner9... failed to open (Invalid argument)
checking /dev/usbscanner10... failed to open (Invalid argument)
checking /dev/usbscanner11... failed to open (Invalid argument)
checking /dev/usbscanner12... failed to open (Invalid argument)
checking /dev/usbscanner13... failed to open (Invalid argument)
checking /dev/usbscanner14... failed to open (Invalid argument)
checking /dev/usbscanner15... failed to open (Invalid argument)
  # No USB scanners found. If you expected something different, make sure that
  # you have loaded a kernel driver for your USB host controller and have setup
  # the USB system correctly. See man sane-usb for details.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.
done

Kokeilin noita nettisivuja, mutten ihan tajunnut mitä sieltä olisin tehnyt. :/

[Thinkit]

Oisko niin että on paketteja asentelematta.

1. Asenna synapticilla paketit
sane
sane-utils
xsane
xsane-common
libsane
libsane-extras

2. Sitten päätteeseen

Koodia: [Valitse]

sudo modprobe sg
3.Taas päätteeseen

Koodia: [Valitse]

sudo vim /etc/modules
4.Päätettä

Koodia: [Valitse]

sudo sane-find-scanner
Kokeile tuota ja ilmoita kuinka kävi.

t: Antti Nykänen

[AlbertRetro]

Ptruuuuuuuuuuu..........

Koodia: [Valitse]

  # Your SCSI scanner was detected. It may or may not be supported by SANE. Try
  # scanimage -L and read the backend's manpage.
>>>>>>>>>>>>>>>>>

Koodia: [Valitse]

scanimage -L =======================>

[Thinkit]

Jäi huomaamatta tuolta välistä. Sorry.   

[Tuxer]

Eikös tuon pitäisi löytyä esim. suoraan Gimpistä (File -> acquire-> xsane), koska se tuolla sane-findillä löytyi?

[Tepi]

Ptruuuuuuuuuuu..........

Koodia: [Valitse]

  # Your SCSI scanner was detected. It may or may not be supported by SANE. Try
  # scanimage -L and read the backend's manpage.
>>>>>>>>>>>>>>>>>

Koodia: [Valitse]

scanimage -L =======================>

No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).


Mutta kun laitoin komennon: sudo sane-find-scanner
tuli tälläinen:
  # sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

found SCSI scanner "UMAX Astra 1220S V1.2" at /dev/sg0
  # Your SCSI scanner was detected. It may or may not be supported by SANE. Try
  # scanimage -L and read the backend's manpage.

  # No USB scanners found. If you expected something different, make sure that
  # you have loaded a kernel driver for your USB host controller and have setup
  # the USB system correctly. See man sane-usb for details.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.

Eli jotenkin Ubuntu ainakin tajuaa että siellä taitaa olla skanneri.

[Thinkit]

Elikkäs scanneri löytyi joten jatketaan.

Koodia: [Valitse]

scanimage -L
Mitä tulostuu tuosta?

[Tepi]

Elikkäs scanneri löytyi joten jatketaan.

Koodia: [Valitse]

scanimage -L
Mitä tulostuu tuosta?

Tuollainen tuli:
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).

[Tuxer]

No entäpä tämä:

Koodia: [Valitse]

scanimage >image.pnm
Edit: eipä varmaan auta koska tuo listaus ei antanut mitään. Entä jos laittaa sudon eteen? (arvailua vaan)

[Tepi]

No entäpä tämä:

Koodia: [Valitse]

scanimage >image.pnm
Edit: eipä varmaan auta koska tuo listaus ei antanut mitään. Entä jos laittaa sudon eteen? (arvailua vaan)

Sudon kun laitoin niin alkoi auttamaan:
device `umax:/dev/sg0' is a UMAX     Astra 1220S      flatbed scanner
Ja kun laitoin tuon scanimage >image.pnm:n, skanneri alkoi heräillä.
Skanneri skannasi, ja kotikansioon tuli tiedosto image.pnm

Kiitoksia, homma toimii. Skanneria ei tosin näy missään graafisesti, tai en ainakaan löydä sitä.
E: Saako tuolal tehtyä muuta kuin pnm-tiedostoja, ja saako tarkkuutta määriteltyä tarkemmin?

[Thinkit]

This problem is due to UDEV but can be overcome via various means, one is to change the permissions of the /dev/sg0 itself. A draw back using this method is yes you can set the permissions and yes it will work for as long as you are logged in, when you reboot you will have to repeat this sequence. Not an option that appeals to us so we modified the Udev rules file. Change directory to the following location

Elikkäs tuo toimii vaan sen istunnon ajan kun olet ubuntussa, kun käynnistät koneen uudelleen joutuu sen taas etsimään uudelleen, joten....

1.

Koodia: [Valitse]

cd /etc/udev/rules.d
2.

Koodia: [Valitse]

sudo vim 40-permissions.rules
3.ja kun aukeaa mene tiedoston loppuun asti hiiren rullalla tahi nuolinäppäimellä ja kun pääset alas asti paina insert näppäintä (PrtScn,SysRq) sen jälkeen mene viimeisen teksirivin loppuun ja paina enter että päästää uudelle tyhjälle riville

Lisää tämä rivi kopioimalla se sinne
 

Koodia: [Valitse]

KERNEL=="sg[0-9]*", GROUP="scanner", MODE="0666"
ja paina sen jälkeen Ctrl+alt+z

Now even if you reboot you have access to the scanner as ordinary user.

T: Antti Nykänen

[Tuxer]

Kiitoksia, homma toimii. Skanneria ei tosin näy missään graafisesti, tai en ainakaan löydä sitä.

Hienoa!

E: Saako tuolal tehtyä muuta kuin pnm-tiedostoja, ja saako tarkkuutta määriteltyä tarkemmin?

Ongelma on siinä, että Ubuntu ei anna tavan käyttäjän käyttää tuota porttia ilman root-oikeuksia.

Mitä sanoo:

Koodia: [Valitse]

ls- al /dev/sg0
EDIT: ilmeisesti tuo Antin vastaus auttaa tuohon ongelmaan, jonka jälkeen voit käyttää graafisia työkaluja (Xsane).
EDIT2: vim:in sijaan voit käyttää tietysti myös esim. gedit:iä (sudo gedit tiedostonimi)

[AlbertRetro]

Aploodeja!!!
Siivosin tuota manuaalia hieman. Hyvä homma kun lähtee vanhatkin koneet  hyrisemään.

albert@kompakkitest:~$ scanimage -h
Usage: scanimage [OPTION]...
Start image acquisition on a scanner device and write PNM image data to standard output.
Parameters are separated by a blank from single-character options (e.g. -d epson) and by a "=" from multi-character options (e.g. --device-name=epson).

-d, --device-name=DEVICE   use a given scanner device (e.g. hp:/dev/scanner)    --format=pnm|tiff      file format of output file
-i, --icc-profile=PROFILE  include this ICC profile into TIFF file
-L, --list-devices         show available scanner devices
-f, --formatted-device-list=FORMAT similar to -L, but the FORMAT of the output can be specified: %d (device name), %v (vendor), %m (model), %t (type), and %i (index number)
-b, --batch[=FORMAT]       working in batch mode, FORMAT is `out%d.pnm' or `out%d.tif' by default depending on --format
    --batch-start=#        page number to start naming files with
    --batch-count=#        how many pages to scan in batch mode
    --batch-increment=#    increase number in filename by an amount of #
    --batch-double         increment page number by two for 2sided originals
                           being scanned in a single sided scanner
    --batch-prompt         ask for pressing a key before scanning a page
    --accept-md5-only      only accept authorization requests using md5

-p, --progress             print progress messages
-n, --dont-scan            only set options, don't actually scan
-T, --test                 test backend thoroughly
-h, --help                 display this help message and exit
-v, --verbose              give even more status messages
-B, --buffer-size          change default input buffersize
-V, --version              print version information

scanimage: no SANE devices found
albert@kompakkitest:~$

Koodia: [Valitse]

SEE ALSO
       sane(7), gamma4scanimage(1), xscanimage(1), xcam(1), xsane(1), scanadf(1), sane-dll(5), sane-net(5), sane-"backendname"(5)

[Tepi]

Noniin, nyt ei kysele enää salsanoja tai mitään. Löysin sen xsane-ohjelmankin jolla pystyy hyvin säätelemään asetuksia. Paljon parempi kuin Xp:n ohjelma.