Kirjoittaja Aihe: pinnacle PCTV DVB-T Stick solo toimaan  (Luettu 20618 kertaa)

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
pinnacle PCTV DVB-T Stick solo toimaan
« : 07.08.08 - klo:22.31 »
Kyseessä on siis usb tikku.
Omistan tälläisen tikun ja en ole saanut sitä toimimaan ubuntussa, olisiko neuvoja?

kirjoitin lsusb niin se löytää  Bus 005 Device 004: ID 2304:0236 Pinnacle Systems, Inc. [hex]
olen kaffeinella koittanut, mutta en tiedä mitä laittaa noihin portteihin.. mistä saan tietää mitä niihin pitäisi laittaa? keffeine sanoo vain "Can't bind info socket!!!" auttakaa joku pikkusen. =)
tai onko parempia ohjelmia kuin keffeine?

olen asentanut myöskin uusimmat v4l ajurit.

toivottavasti löytyy jokin ratkaisu niin tikku pääsee käyttöön :)
« Viimeksi muokattu: 07.08.08 - klo:22.59 kirjoittanut newbie- »

crope

  • Käyttäjä
  • Viestejä: 817
  • Fedora 12
    • Profiili
    • http://palosaari.fi/
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #1 : 07.08.08 - klo:23.02 »
Kyllä sen pitäisi toimia uusimmilla v4l-dvb-ajureilla. Mitäs dmesg-komento sanoo kun pistät tikun sisään? Onhan sulla DIBCOMin firmware asennettuna....

Antti

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #2 : 07.08.08 - klo:23.26 »
jaa en ole varma onko minulla se?
 dvb-usb: found a 'Pinnacle PCTV 72e' in cold state, will try to load a firmware
[   54.801171] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
[   55.006079] usbcore: registered new interface driver dvb_usb_dib0700
[   55.170886] lp: driver loaded but no devices found
[   55.260694] Adding 6072528k swap on /dev/sda5.  Priority:-1 extents:1 across:


crope

  • Käyttäjä
  • Viestejä: 817
  • Fedora 12
    • Profiili
    • http://palosaari.fi/
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #3 : 08.08.08 - klo:00.03 »
Pitäs tuohon tulla kyllä enempikin tekstiä... Kun firmware on ladattu niin laite pitäs mennä lämpimäksi, lukee jotain "found in warm state" jne. Tuohonko sinulla tosiaan ne tulosteet loppuivat?

Antti

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #4 : 08.08.08 - klo:00.17 »
[   40.127344] io scheduler noop registered
[   40.127346] io scheduler anticipatory registered
[   40.127348] io scheduler deadline registered
[   40.127359] io scheduler cfq registered (default)
[   40.127450] Boot video device is 0000:01:00.0
[   40.127454] PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
[   40.127537] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   40.127570] assign_interrupt_mode Found MSI capability
[   40.127598] Allocate Port Service[0000:00:01.0:pcie00]
[   40.127782] isapnp: Scanning for PnP cards...
[   40.480468] isapnp: No Plug & Play device found
[   40.500790] Real Time Clock Driver v1.12ac
[   40.500940] hpet_resources: 0xfed00000 is busy
[   40.500975] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   40.501898] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   40.501953] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   40.502064] PNP: No PS/2 controller found. Probing ports directly.
[   40.504459] serio: i8042 KBD port at 0x60,0x64 irq 1
[   40.504463] serio: i8042 AUX port at 0x60,0x64 irq 12
[   40.522458] mice: PS/2 mouse device common for all mice
[   40.522576] EISA: Probing bus 0 at eisa.0
[   40.522602] EISA: Detected 0 cards.
[   40.522605] cpuidle: using governor ladder
[   40.522607] cpuidle: using governor menu
[   40.522679] NET: Registered protocol family 1
[   40.522704] Using IPI No-Shortcut mode
[   40.522730] registered taskstats version 1
[   40.522818]   Magic number: 4:135:647
[   40.522845]   hash matches device ptydc
[   40.522889] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   40.522891] EDD information not available.
[   40.523049] Freeing unused kernel memory: 368k freed
[   41.703212] fuse init (API version 7.9)
[   41.715190] ACPI: Fan [FAN] (on)
[   41.720242] ACPI: SSDT 7FEE7E00, 01B7 (r1 HPQOEM SLIC-CPC 42302E31 AWRD        0)
[   41.720544] ACPI: SSDT 7FEE8210, 00CE (r1 HPQOEM SLIC-CPC 42302E31 AWRD        0)
[   41.720679] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   41.720688] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   41.721914] ACPI: Thermal Zone [THRM] (19 C)
[   41.891352] usbcore: registered new interface driver usbfs
[   41.891373] usbcore: registered new interface driver hub
[   41.892024] usbcore: registered new device driver usb
[   41.901070] USB Universal Host Controller Interface driver v3.0
[   41.901124] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 17
[   41.901135] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   41.901138] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   41.901365] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   41.901430] uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000ff00
[   41.901547] usb usb1: configuration #1 chosen from 1 choice
[   41.901570] hub 1-0:1.0: USB hub found
[   41.901574] hub 1-0:1.0: 2 ports detected
[   42.004928] ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 18
[   42.004939] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   42.004942] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   42.004964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   42.005027] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000fe00
[   42.005122] usb usb2: configuration #1 chosen from 1 choice
[   42.005141] hub 2-0:1.0: USB hub found
[   42.005145] hub 2-0:1.0: 2 ports detected
[   42.019856] SCSI subsystem initialized
[   42.058334] libata version 3.00 loaded.
[   42.101699] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[   42.101703] e100: Copyright(c) 1999-2006 Intel Corporation
[   42.108769] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
[   42.108780] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   42.108784] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   42.108813] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   42.108876] uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000fd00
[   42.108968] usb usb3: configuration #1 chosen from 1 choice
[   42.108989] hub 3-0:1.0: USB hub found
[   42.108993] hub 3-0:1.0: 2 ports detected
[   42.212561] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[   42.212572] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[   42.212575] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   42.212596] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   42.212659] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
[   42.212754] usb usb4: configuration #1 chosen from 1 choice
[   42.212775] hub 4-0:1.0: USB hub found
[   42.212779] hub 4-0:1.0: 2 ports detected
[   42.243431] usb 1-1: new full speed USB device using uhci_hcd and address 2
[   42.316403] ahci 0000:00:1f.2: version 3.0
[   42.316434] ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 19 (level, low) -> IRQ 18
[   42.406711] usb 1-1: configuration #1 chosen from 1 choice
[   42.646748] usb 2-2: new full speed USB device using uhci_hcd and address 2
[   42.791893] usb 2-2: configuration #1 chosen from 1 choice
[   42.794792] hub 2-2:1.0: USB hub found
[   42.796758] hub 2-2:1.0: 4 ports detected
[   43.145917] usb 4-1: new full speed USB device using uhci_hcd and address 2
[   43.317634] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
[   43.317639] ahci 0000:00:1f.2: flags: 64bit ncq led clo
[   43.317645] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[   43.317873] scsi0 : ahci
[   43.318025] scsi1 : ahci
[   43.318124] scsi2 : ahci
[   43.318224] scsi3 : ahci
[   43.318294] ata1: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe100 irq 222
[   43.318296] ata2: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe180 irq 222
[   43.318299] ata3: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe200 irq 222
[   43.318301] ata4: SATA max UDMA/133 abar m1024@0xfdffe000 port 0xfdffe280 irq 222
[   43.326974] usb 4-1: configuration #1 chosen from 1 choice
[   43.538545] usb 2-2.1: new full speed USB device using uhci_hcd and address 3
[   43.672441] usb 2-2.1: configuration #1 chosen from 1 choice
[   43.675354] hub 2-2.1:1.0: USB hub found
[   43.677314] hub 2-2.1:1.0: 4 ports detected
[   43.793846] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   43.794785] ata1.00: ATA-7: ST3500630AS, 3.CHL, max UDMA/100
[   43.794790] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   43.795774] ata1.00: configured for UDMA/100
[   43.989804] usb 2-2.2: new low speed USB device using uhci_hcd and address 4
[   44.128693] usb 2-2.2: configuration #1 chosen from 1 choice
[   44.268004] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   44.333241] usb 2-2.3: new low speed USB device using uhci_hcd and address 5
[   44.426783] ata2.00: ATAPI: TSSTcorpCD/DVDW TS-H653L, 0514, max UDMA/33, ATAPI AN
[   44.426787] ata2.00: applying bridge limits
[   44.475129] usb 2-2.3: configuration #1 chosen from 1 choice
[   44.582620] ata2.00: configured for UDMA/33
[   44.688659] usb 2-2.1.1: new low speed USB device using uhci_hcd and address 6
[   44.826562] usb 2-2.1.1: configuration #1 chosen from 1 choice
[   44.894945] ata3: SATA link down (SStatus 0 SControl 300)
[   45.044077] usb 2-2.1.4: new full speed USB device using uhci_hcd and address 7
[   45.182927] usb 2-2.1.4: configuration #1 chosen from 1 choice
[   45.187502] usbcore: registered new interface driver libusual
[   45.187727] usbcore: registered new interface driver hiddev
[   45.198806] Initializing USB Mass Storage driver...
[   45.199345] scsi4 : SCSI emulation for USB Mass Storage devices
[   45.199889] usb-storage: device found at 2
[   45.199891] usb-storage: waiting for device to settle before scanning
[   45.204048] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2.2/2-2.2:1.0/input/input1
[   45.211410] ata4: SATA link down (SStatus 0 SControl 300)
[   45.211562] scsi 0:0:0:0: Direct-Access     ATA      ST3500630AS      3.CH PQ: 0 ANSI: 5
[   45.212435] scsi 1:0:0:0: CD-ROM            TSSTcorp CD/DVDW TS-H653L 0514 PQ: 0 ANSI: 5
[   45.212576] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 17
[   45.212588] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   45.212592] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   45.212615] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[   45.216532] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   45.216537] ehci_hcd 0000:00:1d.7: irq 17, io mem 0xfdfff000
[   45.224881] Driver 'sd' needs updating - please use bus_type methods
[   45.224940] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[   45.224950] sd 0:0:0:0: [sda] Write Protect is off
[   45.224952] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   45.224966] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   45.225006] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[   45.225015] sd 0:0:0:0: [sda] Write Protect is off
[   45.225016] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   45.225030] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   45.225033]  sda:<6>input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-2.2
[   45.230183] Driver 'sr' needs updating - please use bus_type methods
[   45.231357] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   45.231504] usb usb5: configuration #1 chosen from 1 choice
[   45.231531] hub 5-0:1.0: USB hub found
[   45.231536] hub 5-0:1.0: 8 ports detected
[   45.243865]  sda1 sda2 < sda5 >
[   45.265393] sd 0:0:0:0: [sda] Attached SCSI disk
[   45.270056] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   45.270074] sr 1:0:0:0: Attached scsi generic sg1 type 5
[   45.274655] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[   45.274659] Uniform CD-ROM driver Revision: 3.20
[   45.274700] sr 1:0:0:0: Attached scsi CD-ROM sr0
[   45.311665] usbcore: registered new interface driver usbhid
[   45.311670] usbcore: registered new interface driver usb-storage
[   45.311674] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   45.311679] USB Mass Storage support registered.
[   45.335402] ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 20
[   45.496927] e100: eth0: e100_probe: addr 0xfdefe000, irq 20, MAC addr 00:1b:fc:f8:a6:7f
[   45.496962] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 20 (level, low) -> IRQ 20
[   45.548657] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20]  MMIO=[fdeff000-fdeff7ff]  Max Packet=[1024]  IR/IT contexts=[8/8]
[   45.556038] ata_piix 0000:00:1f.1: version 2.12
[   45.556054] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 19
[   45.556087] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   45.556720] scsi5 : ata_piix
[   45.557183] scsi6 : ata_piix
[   45.557471] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfb00 irq 14
[   45.557473] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfb08 irq 15
[   45.634298] Attempting manual resume
[   45.634301] swsusp: Resume From Partition 8:5
[   45.634302] PM: Checking swsusp image.
[   45.634399] PM: Resume from disk failed.
[   45.674617] kjournald starting.  Commit interval 5 seconds
[   45.674624] EXT3-fs: mounted filesystem with ordered data mode.
[   45.702578] usb 5-1: new high speed USB device using ehci_hcd and address 2
[   45.720939] ata6: port disabled. ignoring.
[   45.834303] usb 5-1: configuration #1 chosen from 1 choice
[   46.312539] usb 5-7: new high speed USB device using ehci_hcd and address 4
[   46.462012] usb 5-7: configuration #1 chosen from 1 choice
[   46.462609] scsi7 : SCSI emulation for USB Mass Storage devices
[   46.462660] usb-storage: device found at 4
[   46.462662] usb-storage: waiting for device to settle before scanning
[   46.463527] usb 1-1: USB disconnect, address 2
[   46.588084] usb 2-2: USB disconnect, address 2
[   46.588088] usb 2-2.1: USB disconnect, address 3
[   46.588091] usb 2-2.1.1: USB disconnect, address 6
[   46.588304] usb 2-2.1.4: USB disconnect, address 7
[   46.589701] usb 2-2.2: USB disconnect, address 4
[   46.604224] usb 2-2.3: USB disconnect, address 5
[   46.824779] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d80001633e1d]
[   46.847624] usb 2-2: new full speed USB device using uhci_hcd and address 8
[   46.996976] usb 2-2: configuration #1 chosen from 1 choice
[   46.999893] hub 2-2:1.0: USB hub found
[   47.001866] hub 2-2:1.0: 4 ports detected
[   47.111252] usb 4-1: USB disconnect, address 2
[   47.440146] usb 2-2.1: new full speed USB device using uhci_hcd and address 9
[   47.574036] usb 2-2.1: configuration #1 chosen from 1 choice
[   47.576965] hub 2-2.1:1.0: USB hub found
[   47.578920] hub 2-2.1:1.0: 4 ports detected
[   47.891405] usb 2-2.2: new low speed USB device using uhci_hcd and address 10
[   48.030277] usb 2-2.2: configuration #1 chosen from 1 choice
[   48.049379] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2.2/2-2.2:1.0/input/input2
[   48.061606] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-2.2
[   48.266791] usb 2-2.3: new low speed USB device using uhci_hcd and address 11
[   48.412658] usb 2-2.3: configuration #1 chosen from 1 choice
[   48.430769] input: Justcom Technology USB KVM Switch as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2.3/2-2.3:1.0/input/input3
[   48.440973] input,hidraw1: USB HID v1.10 Keyboard [Justcom Technology USB KVM Switch] on usb-0000:00:1d.1-2.3
[   48.453682] input: Justcom Technology USB KVM Switch as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2.3/2-2.3:1.1/input/input4
[   48.464924] input,hidraw2: USB HID v1.10 Mouse [Justcom Technology USB KVM Switch] on usb-0000:00:1d.1-2.3
[   48.670128] usb 2-2.1.1: new low speed USB device using uhci_hcd and address 12
[   48.799022] usb 2-2.1.1: configuration #1 chosen from 1 choice
[   48.816118] input: Gaming Keyboard as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2.1/2-2.1.1/2-2.1.1:1.0/input/input5
[   48.832276] input,hidraw3: USB HID v1.10 Keyboard [Gaming Keyboard] on usb-0000:00:1d.1-2.1.1
[   48.864876] input: Gaming Keyboard as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2.1/2-2.1.1/2-2.1.1:1.1/input/input6
[   48.876232] input,hiddev96,hidraw4: USB HID v1.10 Device [Gaming Keyboard] on usb-0000:00:1d.1-2.1.1
[   49.081454] usb 2-2.1.4: new full speed USB device using uhci_hcd and address 13
[   49.228317] usb 2-2.1.4: configuration #1 chosen from 1 choice
[   49.237329] input: G15 Keyboard G15 Keyboard as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2.1/2-2.1.4/2-2.1.4:1.0/input/input7
[   49.247587] input,hiddev97,hidraw5: USB HID v1.11 Keypad [G15 Keyboard G15 Keyboard] on usb-0000:00:1d.1-2.1.4
[   51.459027] usb-storage: device scan complete
[   51.465506] scsi 7:0:0:0: Direct-Access     Generic- Compact Flash    1.00 PQ: 0 ANSI: 0 CCS
[   51.471996] scsi 7:0:0:1: Direct-Access     Generic- SM/xD-Picture    1.00 PQ: 0 ANSI: 0 CCS
[   51.478610] scsi 7:0:0:2: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[   51.485233] scsi 7:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.00 PQ: 0 ANSI: 0 CCS
[   51.486616] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[   51.486660] sd 7:0:0:0: Attached scsi generic sg2 type 0
[   51.487735] sd 7:0:0:1: [sdc] Attached SCSI removable disk
[   51.487774] sd 7:0:0:1: Attached scsi generic sg3 type 0
[   51.488855] sd 7:0:0:2: [sdd] Attached SCSI removable disk
[   51.488895] sd 7:0:0:2: Attached scsi generic sg4 type 0
[   51.489983] sd 7:0:0:3: [sde] Attached SCSI removable disk
[   51.490024] sd 7:0:0:3: Attached scsi generic sg5 type 0
[   52.496741] input: PC Speaker as /devices/platform/pcspkr/input/input8
[   52.517631] Linux agpgart interface v0.102
[   52.565928] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   52.574790] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   52.843011] input: Power Button (FF) as /devices/virtual/input/input9
[   52.906382] ACPI: Power Button (FF) [PWRF]
[   52.906450] input: Power Button (CM) as /devices/virtual/input/input10
[   52.966257] ACPI: Power Button (CM) [PWRB]
[   53.506652] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[   53.506674] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   53.538078] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[   53.571357] nvidia: module license 'NVIDIA' taints kernel.
[   54.007293] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   54.007302] PCI: Setting latency timer of device 0000:01:00.0 to 64
[   54.007384] NVRM: loading NVIDIA UNIX x86 Kernel Module  169.12  Thu Feb 14 17:53:07 PST 2008
[   54.135386] dib0700: loaded with support for 7 different device-types
[   54.135843] dvb-usb: found a 'Pinnacle PCTV 72e' in cold state, will try to load a firmware
[   54.801171] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
[   55.006079] usbcore: registered new interface driver dvb_usb_dib0700
[   55.170886] lp: driver loaded but no devices found
[   55.260694] Adding 6072528k swap on /dev/sda5.  Priority:-1 extents:1 across:6072528k
[   55.792727] EXT3 FS on sda1, internal journal
[   56.967238] ip_tables: (C) 2000-2006 Netfilter Core Team
[   57.328912] No dock devices found.
[   58.377744] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[   58.377748] apm: disabled - APM is not SMP safe.
[   58.491621] ppdev: user-space parallel port driver
[   58.636683] audit(1218137801.574:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5194 profile="/usr/sbin/cupsd" namespace="default"
[   58.764138] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   58.764144] vboxdrv: Successfully done.
[   58.764192] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   58.764195] vboxdrv: Successfully loaded version 1.5.6_OSE (interface 0x00050002).
[   59.963163] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[   60.053720] Bluetooth: Core ver 2.11
[   60.053977] NET: Registered protocol family 31
[   60.053982] Bluetooth: HCI device and connection manager initialized
[   60.053986] Bluetooth: HCI socket layer initialized
[   60.080402] Bluetooth: L2CAP ver 2.9
[   60.080408] Bluetooth: L2CAP socket layer initialized
[   60.151771] Bluetooth: RFCOMM socket layer initialized
[   60.151969] Bluetooth: RFCOMM TTY layer initialized
[   60.151973] Bluetooth: RFCOMM ver 1.8
[   64.402174] NET: Registered protocol family 17
[   70.456805] NET: Registered protocol family 10
[   70.457120] lo: Disabled Privacy Extensions
[   80.618199] eth0: no IPv6 routers present

kaikki eivät mahtuneet koska suurin sallitty määrä on 20000 merkkiä.

crope

  • Käyttäjä
  • Viestejä: 817
  • Fedora 12
    • Profiili
    • http://palosaari.fi/
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #5 : 08.08.08 - klo:00.20 »
Syystä tai kolmannesta dvb-laite ei näyttäisi lähtevän ajamaan firmwarea. Kokeile bootata, asentaa ajurit uudelleen ja asentaa firmware uudelleen. Vähän hämärä homma, ei voi sanoa mikä mättää.

Antti

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #6 : 08.08.08 - klo:12.07 »
ei toimi.
tämän ohjeen mukan olen tehnyt:

Koodia: [Valitse]
wget http://www.barbak.org/v4l_for_72e_dongle.tar.bz2

tar xvjf v4l_for_72e_dongle.tar.bz2
cd v4l-dvb
sudo cp firmware/dvb-usb-dib0700-1.10.fw /lib/firmware/
make all
sudo make install
sudo reboot

sanokaa jos jotain pitää tehdä eritavalla.

crope

  • Käyttäjä
  • Viestejä: 817
  • Fedora 12
    • Profiili
    • http://palosaari.fi/
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #7 : 08.08.08 - klo:14.51 »
sanokaa jos jotain pitää tehdä eritavalla.

Koodia: [Valitse]
sudo apt-get install mercurial linux-headers-$(uname -r) build-essential
rm -rf v4l-dvb
hg clone http://linuxtv.org/hg/v4l-dvb/
cd v4l-dvb
make distclean
make
sudo make install
sudo make rmmod
<käytä tikkua pois>

Antti

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #8 : 08.08.08 - klo:15.05 »
bootinko nyt koneen kun olen käyttäny tikkua pois? vai mitäs?

timsku

  • Käyttäjä
  • Viestejä: 225
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #9 : 08.08.08 - klo:15.14 »
Nuo ajurit tosiaan joutuu kääntämään uudestaan kernelin vaihtuessa. Itsellä on juuri tuo sama tikku, todella tyytyväinen olen. Ainoa mikä siitä uupuu, on kaukosäädin. Vastaanotinhan tuossa on, vielä en ole ehtinyt perehtyä lirc:n niin paljoa että saisin sen toimimaan yleismallin kakella. Dmesg näyttää kuitenkin lupaavasti seuraavaa kun kokeilee vaikka eräällä philipsin tv-koodilla: [ 1115.418620] dib0700: Unknown remote controller key:  0 11  1  0 Toisesta yleismallistani löytyy myös yksi pinnaclen dvbt-koodi mutta sillä ei saa dmesg:iä näyttämään mitään, vai onko tuo nyt sitten niin että dmesg näyttää vain tuntemattomat koodit... :-\

Kokeile newbie- mitä dmesg näyttää sen jälkeen kun tökkäät tikun kiinni. Itsellä näkyy seuraavaa:

[ 1471.007618] usb 3-1: new high speed USB device using ehci_hcd and address 5
[ 1471.139984] usb 3-1: configuration #1 chosen from 1 choice
[ 1471.146854] dvb-usb: found a 'Pinnacle PCTV 72e' in cold state, will try to load a firmware
[ 1471.162339] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
[ 1471.406367] dib0700: firmware started successfully.
[ 1471.905917] dvb-usb: found a 'Pinnacle PCTV 72e' in warm state.
[ 1471.905985] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 1471.907243] DVB: registering new adapter (Pinnacle PCTV 72e)
[ 1472.142519] DVB: registering frontend 0 (DiBcom 7000PC)...
[ 1472.330133] DiB0070: successfully identified
[ 1472.330240] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:02.2/usb3/3-1/input/input8
[ 1472.357304] dvb-usb: schedule remote query interval to 150 msecs.
[ 1472.357314] dvb-usb: Pinnacle PCTV 72e successfully initialized and connected.


 

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #10 : 08.08.08 - klo:15.17 »
 54.926666] dib0700: loaded with support for 7 different device-types
[   54.928915] dvb-usb: found a 'Pinnacle PCTV 72e' in cold state, will try to load a firmware
[   55.585195] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
[   55.790150] usbcore: registered new interface driver dvb_usb_dib0700
[   55.937442] lp: driver loaded but no devices found
[   56.022203] Adding 6072528k swap on /dev/sda5.  Priority:-1 extents:1 across:6072528k
[   56.558983] EXT3 FS on sda1, internal journal
[   57.658955] ip_tables: (C) 2000-2006 Netfilter Core Team
[   58.020634] No dock devices found.
[   59.061206] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[   59.061211] apm: disabled - APM is not SMP safe.
[   59.166684] ppdev: user-space parallel port driver
[   59.280814] audit(1218187455.459:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5160 profile="/usr/sbin/cupsd" namespace="default"
[   59.414341] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   59.414348] vboxdrv: Successfully done.

ei taida toimia vieläkään

timsku

  • Käyttäjä
  • Viestejä: 225
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #11 : 08.08.08 - klo:15.21 »
Boottaa ilman tikkua, kun kone on kunnolla käynnistynyt tökkää tikku ja koita uudestaan...

Sulta puuttuu seuraava:
[ 1471.406367] dib0700: firmware started successfully.

Eli saattaa johtua siitä että ei oo jostain syystä onnistunu lataamaan firmistä. Onhan firmware varmasti oikeassa paikassa, itselläni se on paikassa: /lib/firmware/2.6.24-19-generic/dvb-usb-dib0700-1.10.fw
Eli tarkista konsolissa uname -r käskyllä mikä kerneli ja onko vastaavassa paikassa...
« Viimeksi muokattu: 08.08.08 - klo:15.28 kirjoittanut timsku »

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #12 : 08.08.08 - klo:15.31 »
pitäisikö toiminnan näkyä jotenkin? nyt olen ottanut tikun irti ja boottinut ja laitoin takaisin.

crope

  • Käyttäjä
  • Viestejä: 817
  • Fedora 12
    • Profiili
    • http://palosaari.fi/
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #13 : 08.08.08 - klo:15.39 »
pitäisikö toiminnan näkyä jotenkin? nyt olen ottanut tikun irti ja boottinut ja laitoin takaisin.
No ilmestyykö sinne dmesg-tulosteeseen mitään uutta? Sieltä sen näkee heti jos se alkaa toimimaan.

Antti

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #14 : 08.08.08 - klo:15.41 »
Boottaa ilman tikkua, kun kone on kunnolla käynnistynyt tökkää tikku ja koita uudestaan...

Sulta puuttuu seuraava:
[ 1471.406367] dib0700: firmware started successfully.

Eli saattaa johtua siitä että ei oo jostain syystä onnistunu lataamaan firmistä. Onhan firmware varmasti oikeassa paikassa, itselläni se on paikassa: /lib/firmware/2.6.24-19-generic/dvb-usb-dib0700-1.10.fw
Eli tarkista konsolissa uname -r käskyllä mikä kerneli ja onko vastaavassa paikassa...


juu, tuolla on /lib/firmware/2.6.24-19-generic/dvb-usb-dib0700-1.10.fw
ja ydin linux on 2.6.24-19-generic

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #15 : 08.08.08 - klo:15.43 »
[  339.835745] dvb-usb: found a 'Pinnacle PCTV 72e' in cold state, will try to load a firmware
[  339.875026] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
[  340.083367] usbcore: registered new interface driver dvb_usb_dib0700

nuo ovat alimmaisena.

crope

  • Käyttäjä
  • Viestejä: 817
  • Fedora 12
    • Profiili
    • http://palosaari.fi/
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #16 : 08.08.08 - klo:15.45 »
mari@mari-laptop:~/antin/v4l-dvb/firmware$ md5sum dvb-usb-dib0700-1.10.fw
0b39b8cceb1ccdb86d6fc932149aff25  dvb-usb-dib0700-1.10.fw
mari@mari-laptop:~/antin/v4l-dvb/firmware$ md5sum /lib/firmware/2.6.24-19-generic/dvb-usb-dib0700-1.10.fw
5878ebfcba2d8deb90b9120eb89b02da  /lib/firmware/2.6.24-19-generic/dvb-usb-dib0700-1.10.fw
mari@mari-laptop:~/antin/v4l-dvb/firmware$

Siinä on syy. Siellä on näköjään rikkinäinen firmware tuossa paketissa jonka olet alun alkaen asentanut (sitä ei olis kannattanut asentaa). Poista se firmwareja käytä sitä mikä tulee paketinhallinan mukana.

Antti

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #17 : 08.08.08 - klo:15.47 »
mari@mari-laptop:~/antin/v4l-dvb/firmware$ md5sum dvb-usb-dib0700-1.10.fw
0b39b8cceb1ccdb86d6fc932149aff25  dvb-usb-dib0700-1.10.fw
mari@mari-laptop:~/antin/v4l-dvb/firmware$ md5sum /lib/firmware/2.6.24-19-generic/dvb-usb-dib0700-1.10.fw
5878ebfcba2d8deb90b9120eb89b02da  /lib/firmware/2.6.24-19-generic/dvb-usb-dib0700-1.10.fw
mari@mari-laptop:~/antin/v4l-dvb/firmware$

Siinä on syy. Siellä on näköjään rikkinäinen firmware tuossa paketissa jonka olet alun alkaen asentanut (sitä ei olis kannattanut asentaa). Poista se firmwareja käytä sitä mikä tulee paketinhallinan mukana.

Antti

anteeksi olen vasta asentanut ubuntun niin en tiedä kaikkea, kuinka poistan sen? en oikeen tajunnut mikä pitää poistaa

crope

  • Käyttäjä
  • Viestejä: 817
  • Fedora 12
    • Profiili
    • http://palosaari.fi/
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #18 : 08.08.08 - klo:15.50 »
anteeksi olen vasta asentanut ubuntun niin en tiedä kaikkea, kuinka poistan sen? en oikeen tajunnut mikä pitää poistaa

sudo rm -f /lib/firmware/dvb-usb-dib0700-1.10.fw

adjektiivi

  • Käyttäjä
  • Viestejä: 315
    • Profiili
Vs: pinnacle PCTV DVB-T Stick solo toimaan
« Vastaus #19 : 08.08.08 - klo:15.52 »
nyt on poistettu, mitäs sitten?