Kirjoittaja Aihe: Gembird Muistikortinlukija, 5,25", USB, FW, Audio, valk.[ratkaistu]  (Luettu 2429 kertaa)

Bacardi

  • Käyttäjä
  • Viestejä: 24
    • Profiili
Haluaisin ostaa tuommoisen, tai on jo tilauksessa http://www.jimmspc-store.fi/tuote/UHB-2MP mutta toimiiko tuo ubuntussa 7.10 ? jos ei, niin löytyykö mitään vastaavaa, joka toimii?
« Viimeksi muokattu: 13.06.08 - klo:15.01 kirjoittanut Elias »
If you can't explain something to a six-year-old, you really don't understand it yourself:  Albert Einstein

Bacardi

  • Käyttäjä
  • Viestejä: 24
    • Profiili
Haluaisin ostaa tuommoisen, tai on jo tilauksessa http://www.jimmspc-store.fi/tuote/UHB-2MP mutta toimiiko tuo ubuntussa 7.10 ? jos ei, niin löytyykö mitään vastaavaa, joka toimii?

Vehje on nyt ostettu ja apua tarvitsisin, eli tuossa on asennusohje linuxiin:

/*** Installation guide for Linux ***/
This document was modified from "http://www.linux-usb.org/USB-guide/book1.html" which was written by Brad Hards.

System Requirement:

1. kernel versions 2.2.7 and later contain the USB code.


Install Card Reader step by step:

1. configure USB into kernel. Use of "make menuconfig" is recommended.
   Under "USB support", you need to select "Support for USB". You also need to
   select either UHCI (Intel PIIX4, VIA, ...) support, UHCI Alternate Driver (JE) support
   or OHCI-HCD (Compaq, iMacs, OPTi, SiS, ALi, ...) support. Which one you select is
   dependent on what kind of motherboard or adapter you have.

2. select "USB Mass Storage support"

3. select "Preliminary USB Device Filesystem"

4. select "SCSI support"

5. selct "SCSI disk support"

6. select "/proc support"

7. Rebuild the kernel and the modules (if you configured to build as modules),
   and install the new kernel and the new modules. Reboot the system.
   If you are using modules, you need to load the following modules:
   a. usbcore.o
   b. usb-uhci.o, uhci.o or usb-ohci.o
   c. usb-storage.o

   Inspect the kernel logs. If there isn't anything that could be USB related,
   likely causes are use of the wrong driver (UHCI when you needed OHCI or
   OHCI when you needed UHCI), not physically installing the hardware,
   a BIOS configuration that disables USB or stuffing up the configuration or
   installation of the kernel.

8. Use the mount command: mount -t usbdevfs none /proc/bus/usb.
   Note that the 'none' keyword is arbitrary.

   If you do not want to have to mount the filesystem each time you reboot the system,
   you can add the following to /etc/fstab after the /proc entry.

   none            /proc/bus/usb             usbdevfs        defaults   0   0

9. Edit /etc/fstab
   The exact syntax depends on the Card Reader. The best way is to make suitable entries
   in /etc/fstab. The suitable entries for Card Reader would be:

   /dev/sda    /mnt/SMC       auto            noauto,user 0   0
   /dev/sdb    /mnt/CFC       auto            noauto,user 0   0
   /dev/sdc    /mnt/SDC       auto            noauto,user 0   0
   /dev/sdd    /mnt/MSC       auto            noauto,user 0   0

10. Create matching mount points in the actual filesystem:
   mkdir /mnt/SMC
   mkdir /mnt/CFC
   mkdir /mnt/SDC
   mkdir /mnt/MSC

11. Mount Card Reader:
   mount /dev/sda
   mount /dev/sdb
   mount /dev/sdc
   mount /dev/sdd

Note:
   Note that the above entries assume you have no other SCSI devices.
   If you do have other devices, then the USB disk may not be /dev/sda,
   but could instead be /dev/sdb, /dev/sdc or some other device.


« Viimeksi muokattu: 13.05.08 - klo:15.36 kirjoittanut Bacardi »
If you can't explain something to a six-year-old, you really don't understand it yourself:  Albert Einstein

roki

  • Käyttäjä
  • Viestejä: 192
  • Ubuntu Studio
    • Profiili
    • koti Sivu
Kyllä tuon pitäisi toimia ihan ilman säätämisiä. Ei muuta kuin piuhat kiinni ja koeajolle.

Linuxin käyttäjä kernelin versiosta 1.2.13

Bacardi

  • Käyttäjä
  • Viestejä: 24
    • Profiili
Näköjään toimii heh :)
If you can't explain something to a six-year-old, you really don't understand it yourself:  Albert Einstein