Viestit

1

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 12.04.08 - klo:01.06 »

ei kyllä oo sama malli sillä tässä ei kyllä vipuja ole   Kiitti kuitenkin..

2

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 10.04.08 - klo:15.07 »

Tässäpä pieni päivitys!

Eli laitoin kaiken uusiksi ja päivitin ubuntu 8.04beta versioon. Enää ei tunnista cd asemaksi, mutta ei toimi vieläkään.
Olen tehnyt seuraavat toimenpiteet erään ohjeen mukaan.( http://ubuntuforums.org/showthread.php?t=366644&highlight=WLI-U2-KG54 )
Eli blacklistannut rt 2570 ajurin
asentanut ndiswrapperin ja windowsin ajurit.
tuo kohta ohjeessa jossa tulosteen ndiswrapper -l pitäisi antaa tuloste

netu2g54 : driver installed
device (0411:0066) present (alternate driver: rt2570)

antaa minulla vain tuon ylemmän rivin

tässä tulosteet joita jo aikaisemmin pyydettiin

meme@meme-desktop:~$ lshw -C network
WARNING: you should run this program as super-user.
  *-network               
       description: Ethernet interface
       product: RTL-8139/8139C/8139C+
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 5
       bus info: pci@0000:01:05.0
       logical name: eth0
       version: 10
       serial: 00:11:5b:ee:fd:10
       width: 32 bits
       clock: 33MHz
       capabilities: bus_master cap_list ethernet physical
       configuration: broadcast=yes driver=8139too driverversion=0.9.28 latency=64 maxlatency=64 mingnt=32 module=8139too multicast=yes
meme@meme-desktop:~$


meme@meme-desktop:~$ dmesg |tail -20
[ 1830.999318] sr 6:0:0:0: rejecting I/O to offline device
[ 1830.999351] sr 6:0:0:0: rejecting I/O to offline device
[ 1831.020785] scsi 6:0:0:0: rejecting I/O to dead device
[ 1831.020806] scsi 6:0:0:0: rejecting I/O to dead device
[ 1831.020813] scsi 6:0:0:0: rejecting I/O to dead device
[ 1831.131492] usb 5-2: new high speed USB device using ehci_hcd and address 13
[ 1831.295663] usb 5-2: configuration #1 chosen from 1 choice
[ 1831.334174] input: BUFFALO WLI-U2-KG54-AI as /devices/pci0000:00/0000:00:1d.7/usb5/5-2/5-2:1.0/input/input11
[ 1831.358273] input,hidraw2: USB HID v1.00 Keyboard [BUFFALO WLI-U2-KG54-AI] on usb-0000:00:1d.7-2
[ 1851.426984] usb 5-2: USB disconnect, address 13
[ 1851.722792] usb 5-2: new high speed USB device using ehci_hcd and address 14
[ 1851.887560] usb 5-2: configuration #1 chosen from 1 choice
[ 1851.898524] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1851.907945] usb-storage: device found at 14
[ 1851.907952] usb-storage: waiting for device to settle before scanning
[ 1856.897978] usb-storage: device scan complete
[ 1856.898992] scsi 7:0:0:0: CD-ROM            BUFFALO  WLI-U2-KG54-CD   1.00 PQ: 0 ANSI: 0 CCS
[ 1856.913440] sr1: scsi3-mmc drive: 0x/0x caddy
[ 1856.913522] sr 7:0:0:0: Attached scsi CD-ROM sr1
[ 1856.913576] sr 7:0:0:0: Attached scsi generic sg3 type 5
meme@meme-desktop:~$


Kiitoksia hyvistä vihjeistä, mutta kaikki tuntuu olevan vähän ristiriidassa toisten kanssa. Joissakin pyritään käyttämään tuota rt2570 ajuria ja toisissa sanotaan että se disconnectaa koko ajan.  Ideoita?

3

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 07.04.08 - klo:23.46 »

vähän leikkelin noita tulosteita kun ei saa lähettää kuin 20 000 merkkiä. Jos saatte selvää tai jotain ymmärrätte niin täällä valvon jälleen koko yön

4

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 07.04.08 - klo:23.45 »

Koodia: [Valitse]

meme@meme:~$ dmesg
[    0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003f7d0000 (usable)
[    0.000000]  BIOS-e820: 000000003f7d0000 - 000000003f7de000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003f7de000 - 000000003f800000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[    0.000000] 119MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at 000ff780
[    0.000000] Entering add_active_range(0, 0, 260048) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   260048
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   260048
[    0.000000] On node 0 totalpages: 260048
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 239 pages used for memmap
[    0.000000]   HighMem zone: 30433 pages, LIFO batch:7
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP signature @ 0xC00F8B10 checksum 0
[    0.000000] ACPI: RSDP 000F8B10, 0014 (r0 ACPIAM)
[    0.000000] ACPI: RSDT 3F7D0000, 0034 (r1 A M I  OEMRSDT   3000511 MSFT       97)
[    0.000000] ACPI: FACP 3F7D0200, 0084 (r2 A M I  OEMFACP   3000511 MSFT       97)
[    0.000000] ACPI: DSDT 3F7D03F0, 3DB6 (r1   915G  915G-M5        0 INTL  2002026)
[    0.000000] ACPI: FACS 3F7DE000, 0040
[    0.000000] ACPI: APIC 3F7D0390, 005C (r1 A M I  OEMAPIC   3000511 MSFT       97)
[    0.000000] ACPI: OEMB 3F7DE040, 0046 (r1 A M I  AMI_OEM   3000511 MSFT       97)
[    0.000000] ACPI: MCFG 3F7D41B0, 003C (r1 A M I  OEMMCFG   3000511 MSFT       97)
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] Processor #0 15:4 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 40000000 (gap: 3f800000:bf600000)
[    0.000000] Built 1 zonelists.  Total pages: 258017
[    0.000000] Kernel command line: root=UUID=7db492b6-d9ad-46d7-bae8-2b282ee8048c ro quiet splash locale=fi_FI
[    0.000000] mapped APIC to ffffd000 (fee00000)
[    0.000000] mapped IOAPIC to ffffc000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 2793.297 MHz processor.
[   11.658788] Console: colour VGA+ 80x25
[   11.659230] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   11.659864] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   11.684429] Memory: 1019308k/1040192k available (2015k kernel code, 20148k reserved, 916k data, 364k init, 122688k highmem)
[   11.684441] virtual kernel memory layout:
[   11.684442]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[   11.684443]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   11.684444]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   11.684446]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   11.684447]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[   11.684448]       .data : 0xc02f7d26 - 0xc03dce84   ( 916 kB)
[   11.684449]       .text : 0xc0100000 - 0xc02f7d26   (2015 kB)
[   11.684452] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   11.684502] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   11.764397] Calibrating delay using timer specific routine.. 5591.55 BogoMIPS (lpj=11183118)
[   11.764431] Security Framework v1.0.0 initialized
[   11.764440] SELinux:  Disabled at boot.
[   11.764453] Mount-cache hash table entries: 512
[   11.764608] CPU: After generic identify, caps: bfebfbff 00100000 00000000 00000000 0000451d 00000000 00000000
[   11.764618] monitor/mwait feature present.
[   11.764621] using mwait in idle threads.
[   11.764629] CPU: Trace cache: 12K uops, L1 D cache: 16K
[   11.764632] CPU: L2 cache: 256K
[   11.764635] CPU: Hyper-Threading is disabled
[   11.764638] CPU: After all inits, caps: bfebfbff 00100000 00000000 0000b180 0000451d 00000000 00000000
[   11.764649] Compat vDSO mapped to ffffe000.
[   11.764666] Checking 'hlt' instruction... OK.
[   11.780479] SMP alternatives: switching to UP code
[   11.780723] Freeing SMP alternatives: 11k freed
[   11.781040] Early unpacking initramfs... done
[   12.102021] ACPI: Core revision 20070126
[   12.102082] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   12.115606] CPU0: Intel(R) Celeron(R) CPU 2.80GHz stepping 01
[   12.115650] Total of 1 processors activated (5591.55 BogoMIPS).
[   12.115804] ENABLING IO-APIC IRQs
[   12.116001] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   12.259629] Brought up 1 CPUs
[   12.259771] Booting paravirtualized kernel on bare hardware
[   12.259846] Time: 20:17:42  Date: 03/07/108
[   12.259873] NET: Registered protocol family 16
[   12.259991] EISA bus registered
[   12.260011] ACPI: bus type pci registered
[   12.260085] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[   12.260087] PCI: Using configuration type 1
[   12.260089] Setting up standard PCI resources
[   12.271842] ACPI: EC: Look up EC in DSDT
[   12.275919] ACPI: Interpreter enabled
[   12.275924] ACPI: (supports S0 S1 S3 S4 S5)
[   12.275949] ACPI: Using IOAPIC for interrupt routing
[   12.286347] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   12.286357] PCI: Probing PCI hardware (bus 00)
[   12.286940] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[   12.286945] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[   12.287229] PCI: Transparent bridge - 0000:00:1e.0
[   12.287262] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   12.287425] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[   12.294794] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[   12.294919] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[   12.295036] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[   12.295154] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[   12.295271] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[   12.295388] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[   12.295507] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[   12.295690] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[   12.295851] Linux Plug and Play Support v0.97 (c) Adam Belay
[   12.295866] pnp: PnP ACPI init
[   12.295881] ACPI: bus type pnp registered
[   12.301530] pnp: PnP ACPI: found 17 devices
[   12.301535] ACPI: ACPI bus type pnp unregistered
[   12.301539] PnPBIOS: Disabled by ACPI PNP
[   12.301616] PCI: Using ACPI for IRQ routing
[   12.301620] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   12.304690] NET: Registered protocol family 8
[   12.304693] NET: Registered protocol family 20
[   12.304805] pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[   12.304818] pnp: 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[   12.304821] pnp: 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
[   12.304828] pnp: 00:0b: iomem range 0xffc00000-0xfff7ffff could not be reserved
[   12.304833] pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[   12.304837] pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[   12.304843] pnp: 00:0e: ioport range 0x680-0x6ff has been reserved
[   12.304846] pnp: 00:0e: ioport range 0x295-0x296 has been reserved
[   12.304852] pnp: 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
[   12.304858] pnp: 00:10: iomem range 0x0-0x9ffff could not be reserved
[   12.304861] pnp: 00:10: iomem range 0x0-0x0 could not be reserved
[   12.304864] pnp: 00:10: iomem range 0xe0000-0xfffff could not be reserved
[   12.304867] pnp: 00:10: iomem range 0x100000-0x3f7fffff could not be reserved
[   12.307514] Time: tsc clocksource has been installed.
[   12.335277] PCI: Bridge: 0000:00:1e.0
[   12.335281]   IO window: e000-efff
[   12.335289]   MEM window: fbf00000-fbffffff
[   12.335293]   PREFETCH window: disabled.
[   12.335310] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   12.335328] NET: Registered protocol family 2
[   12.371450] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   12.371593] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[   12.372808] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   12.373238] TCP: Hash tables configured (established 131072 bind 65536)
[   12.373243] TCP reno registered
[   12.383575] checking if image is initramfs... it is
[   12.834659] Switched to high resolution mode on CPU 0
[   13.004825] Freeing initrd memory: 7347k freed
[   13.005408] audit: initializing netlink socket (disabled)
[   13.005423] audit(1207599462.016:1): initialized
[   13.005510] highmem bounce pool size: 64 pages
[   13.008334] VFS: Disk quotas dquot_6.5.1
[   13.008419] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   13.008561] io scheduler noop registered
[   13.008564] io scheduler anticipatory registered

5

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 07.04.08 - klo:23.44 »

Koodia: [Valitse]

meme@meme:~$ dmesg
[    0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[   12.259991] EISA bus registered
[   12.260011] ACPI: bus type pci registered
[   12.260085] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[   12.260087] PCI: Using configuration type 1
[   12.260089] Setting up standard PCI resources
[   12.271842] ACPI: EC: Look up EC in DSDT
[   12.275919] ACPI: Interpreter enabled
[   12.275924] ACPI: (supports S0 S1 S3 S4 S5)
[   12.275949] ACPI: Using IOAPIC for interrupt routing
[   12.286347] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   12.286357] PCI: Probing PCI hardware (bus 00)
[   12.286940] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[   12.286945] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[   12.287229] PCI: Transparent bridge - 0000:00:1e.0
[   12.287262] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   12.287425] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[   12.294794] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[   12.294919] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[   12.295036] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[   12.295154] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[   12.295271] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[   12.295388] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[   12.295507] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[   12.295690] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[   12.295851] Linux Plug and Play Support v0.97 (c) Adam Belay
[   12.295866] pnp: PnP ACPI init
[   12.295881] ACPI: bus type pnp registered
[   12.301530] pnp: PnP ACPI: found 17 devices
[   12.301535] ACPI: ACPI bus type pnp unregistered
[   12.301539] PnPBIOS: Disabled by ACPI PNP
[   12.301616] PCI: Using ACPI for IRQ routing
[   12.301620] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   12.304690] NET: Registered protocol family 8
[   12.304693] NET: Registered protocol family 20
[   12.304805] pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[   12.304818] pnp: 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[   12.304821] pnp: 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
[   12.304828] pnp: 00:0b: iomem range 0xffc00000-0xfff7ffff could not be reserved
[   12.304833] pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[   12.304837] pnp: 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[   12.304843] pnp: 00:0e: ioport range 0x680-0x6ff has been reserved
[   12.304846] pnp: 00:0e: ioport range 0x295-0x296 has been reserved
[   12.304852] pnp: 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
[   12.304858] pnp: 00:10: iomem range 0x0-0x9ffff could not be reserved
[   12.304861] pnp: 00:10: iomem range 0x0-0x0 could not be reserved
[   12.304864] pnp: 00:10: iomem range 0xe0000-0xfffff could not be reserved
[   12.304867] pnp: 00:10: iomem range 0x100000-0x3f7fffff could not be reserved
[   12.307514] Time: tsc clocksource has been installed.
[   12.335277] PCI: Bridge: 0000:00:1e.0
[   12.335281]   IO window: e000-efff
[   12.335289]   MEM window: fbf00000-fbffffff
[   12.335293]   PREFETCH window: disabled.
[   12.335310] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   12.335328] NET: Registered protocol family 2
[   12.371450] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   12.371593] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[   12.372808] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   12.373238] TCP: Hash tables configured (established 131072 bind 65536)
[   12.373243] TCP reno registered
[   12.383575] checking if image is initramfs... it is
[   12.834659] Switched to high resolution mode on CPU 0
[   13.004825] Freeing initrd memory: 7347k freed
[   13.005408] audit: initializing netlink socket (disabled)
[   13.005423] audit(1207599462.016:1): initialized
[   13.005510] highmem bounce pool size: 64 pages
[   13.008334] VFS: Disk quotas dquot_6.5.1
[   13.008419] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   13.008561] io scheduler noop registered
[   13.008564] io scheduler anticipatory registered
[   13.008566] io scheduler deadline registered
[   13.008594] io scheduler cfq registered (default)
[   13.008612] Boot video device is 0000:00:02.0
[   13.008892] isapnp: Scanning for PnP cards...
[   13.360312] isapnp: No Plug & Play device found
[   13.443421] Real Time Clock Driver v1.12ac
[   13.443547] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   13.443656] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   13.445184] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   13.446501] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   13.446793] input: Macintosh mouse button emulation as /class/input/input0
[   13.446914] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[   13.446917] PNP: PS/2 controller doesn't have AUX irq; using default 12
[   13.449365] serio: i8042 KBD port at 0x60,0x64 irq 1
[   13.449376] serio: i8042 AUX port at 0x60,0x64 irq 12
[   13.449689] mice: PS/2 mouse device common for all mice
[   13.449865] EISA: Probing bus 0 at eisa.0
[   13.449896] EISA: Detected 0 cards.
[   13.449995] TCP cubic registered
[   13.450014] NET: Registered protocol family 1
[   13.450039] Using IPI No-Shortcut mode
[   13.450234]   Magic number: 4:354:295
[   13.450267]   hash matches device ttyz9
[   13.450281]   hash matches device ttywc
[   13.450398]   hash matches device tty28
[   13.450722] Freeing unused kernel memory: 364k freed
[   13.485623] input: AT Translated Set 2 keyboard as /class/input/input1
[   14.727275] AppArmor: AppArmor initialized<5>audit(1207599463.516:2):  type=1505 info="AppArmor initialized" pid=1193
[   14.737742] fuse init (API version 7.8)
[   14.744071] Failure registering capabilities with primary security module.
[   14.761834] ACPI: Processor [CPU1] (supports 8 throttling states)
[   14.761855] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[   14.763018] ACPI: Thermal Zone [THRM] (-269 C)
[   15.493771] usbcore: registered new interface driver usbfs
[   15.493801] usbcore: registered new interface driver hub
[   15.493834] usbcore: registered new device driver usb
[   15.511461] USB Universal Host Controller Interface driver v3.0
[   15.511539] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
[   15.511552] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   15.511557] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   15.511723] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   15.511758] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000d880
[   15.511900] usb usb1: configuration #1 chosen from 1 choice
[   15.511933] hub 1-0:1.0: USB hub found
[   15.511941] hub 1-0:1.0: 2 ports detected
[   15.561832] SCSI subsystem initialized
[   15.579824] libata version 2.21 loaded.
[   15.614969] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
[   15.614983] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   15.614988] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   15.615017] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   15.615048] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000d800
[   15.615162] usb usb2: configuration #1 chosen from 1 choice
[   15.615198] hub 2-0:1.0: USB hub found
[   15.615207] hub 2-0:1.0: 2 ports detected
[   15.615317] 8139too Fast Ethernet driver 0.9.28
[   15.718006] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[   15.718020] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   15.718025] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   15.718056] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   15.718088] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d480
[   15.718207] usb usb3: configuration #1 chosen from 1 choice
[   15.718240] hub 3-0:1.0: USB hub found
[   15.718249] hub 3-0:1.0: 2 ports detected
[   15.735136] Floppy drive(s): fd0 is 1.44M
[   15.814461] FDC 0 is a post-1991 82077
[   15.821839] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
[   15.821852] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[   15.821857] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   15.821889] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   15.821920] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000d400
[   15.822038] usb usb4: configuration #1 chosen from 1 choice
[   15.822075] hub 4-0:1.0: USB hub found
[   15.822083] hub 4-0:1.0: 2 ports detected
[   15.926557] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
[   15.926576] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   15.926580] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   15.926630] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[   15.926667] ehci_hcd 0000:00:1d.7: debug port 1
[   15.926674] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[   15.926682] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xfbe37c00
[   15.930596] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   15.930710] usb usb5: configuration #1 chosen from 1 choice
[   15.930748] hub 5-0:1.0: USB hub found
[   15.930756] hub 5-0:1.0: 8 ports detected
[   16.036314] ata_piix 0000:00:1f.2: version 2.11
[   16.036323] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[   16.189048] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 17
[   16.189093] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[   16.189200] scsi0 : ata_piix
[   16.189272] scsi1 : ata_piix
[   16.189397] ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
[   16.189402] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
[   16.353094] ata1.00: ATA-7: HDS728080PLA380, PF2OA60A, max UDMA/133
[   16.353099] ata1.00: 160836480 sectors, multi 16: LBA48 NCQ (depth 0/32)
[   16.369094] ata1.00: configured for UDMA/133
[   16.564410] usb 3-1: new low speed USB device using uhci_hcd and address 2
[   16.688447] ata2.00: ATAPI: BCO5232IM, VER 0644, max UDMA/66
[   16.688455] ata2.00: limited to UDMA/33 due to 40-wire cable
[   16.741510] usb 3-1: configuration #1 chosen from 1 choice
[   16.771742] usbcore: registered new interface driver hiddev
[   16.795833] input: Logitech USB Receiver as /class/input/input2
[   16.796077] input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-1
[   16.828311] input: Logitech USB Receiver as /class/input/input3
[   16.828579] input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.2-1
[   16.828602] usbcore: registered new interface driver usbhid
[   16.828606] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   16.860166] ata2.00: configured for UDMA/33
[   16.860309] scsi 0:0:0:0: Direct-Access     ATA      HDS728080PLA380  PF2O PQ: 0 ANSI: 5
[   16.860754] scsi 1:0:0:0: CD-ROM            COMBO    BCO5232IM        0644 PQ: 0 ANSI: 5
[   16.860996] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 20 (level, low) -> IRQ 20
[   16.861395] eth0: RealTek RTL8139 at 0xf883ac00, 00:11:5b:ee:fd:10, IRQ 20
[   16.861398] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[   16.863731] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[   16.878798] sd 0:0:0:0: [sda] 160836480 512-byte hardware sectors (82348 MB)
[   16.878817] sd 0:0:0:0: [sda] Write Protect is off
[   16.878821] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   16.878842] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   16.878917] sd 0:0:0:0: [sda] 160836480 512-byte hardware sectors (82348 MB)
[   16.878930] sd 0:0:0:0: [sda] Write Protect is off
[   16.878933] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   16.878952] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   16.878960]  sda: sda1 sda2 < sda5 >
[   16.912677] sd 0:0:0:0: [sda] Attached SCSI disk
[   16.918068] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   16.918297] sr 1:0:0:0: Attached scsi generic sg1 type 5
[   16.952243] sr0: scsi3-mmc drive: 5x/52x writer cd/rw xa/form2 cdda tray
[   16.952250] Uniform CD-ROM driver Revision: 3.20
[   16.952565] sr 1:0:0:0: Attached scsi CD-ROM sr0
[   17.120455] Attempting manual resume
[   17.120460] swsusp: Resume From Partition 8:5
[   17.120462] PM: Checking swsusp image.
[   17.120670] PM: Resume from disk failed.
[   17.167517] kjournald starting.  Commit interval 5 seconds
[   17.167535] EXT3-fs: mounted filesystem with ordered data mode.
[   24.289840] Linux agpgart interface v0.102 (c) Dave Jones
[   24.332616] agpgart: Detected an Intel 915G Chipset.
[   24.332853] agpgart: Detected 7932K stolen memory.
[   24.349474] agpgart: AGP aperture is 256M @ 0xd0000000
[   24.858810] intel_rng: FWH not detected
[   25.492786] input: PC Speaker as /class/input/input4
[   25.519710] usbcore: registered new interface driver xpad
[   25.519716] /build/buildd/linux-source-2.6.22-2.6.22/drivers/input/joystick/xpad.c: driver for Xbox controllers v0.1.6
[   25.723945] parport_pc 00:08: reported by Plug and Play ACPI
[   25.724059] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   25.727347] iTCO_vendor_support: vendor-support=0
[   25.737269] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[   25.737371] iTCO_wdt: Found a ICH6 or ICH6R TCO device (Version=2, TCOBASE=0x0860)
[   25.737429] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   25.974731] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
[   25.974757] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   27.304958] lp0: using parport0 (interrupt-driven).
[   27.325227] ndiswrapper version 1.45 loaded (smp=yes)
[   27.370146] usbcore: registered new interface driver ndiswrapper
[   27.428428] Adding 3004112k swap on /dev/sda5.  Priority:-1 extents:1 across:3004112k
[   27.650439] EXT3 FS on sda1, internal journal
[   28.737913] input: Power Button (FF) as /class/input/input5
[   28.743116] ACPI: Power Button (FF) [PWRF]
[   28.779438] input: Power Button (CM) as /class/input/input6
[   28.784668] ACPI: Power Button (CM) [PWRB]
[   28.830168] No dock devices found.
[   30.523590] ppdev: user-space parallel port driver
[   30.561791] eth0: link down
[   30.753992] audit(1207599480.092:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4715 profile="/usr/sbin/cupsd"
[   30.817272] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   30.817279] apm: overridden by ACPI.
[   31.026277] Failure registering capabilities with primary security module.
[   31.246461] Bluetooth: Core ver 2.11
[   31.246782] NET: Registered protocol family 31
[   31.246788] Bluetooth: HCI device and connection manager initialized
[   31.246791] Bluetooth: HCI socket layer initialized
[   31.262202] Bluetooth: L2CAP ver 2.8
[   31.262207] Bluetooth: L2CAP socket layer initialized
[   31.318899] Bluetooth: RFCOMM socket layer initialized
[   31.319194] Bluetooth: RFCOMM TTY layer initialized
[   31.319200] Bluetooth: RFCOMM ver 1.8
[   33.078616] [drm] Initialized drm 1.1.0 20060810
[   33.089154] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
[   33.092275] [drm] Initialized i915 1.6.0 20060119 on minor 0
meme@meme:~$




edit. nyt viestiäsi on muokattu, tunnistat sen siitä että tässä jossain kohtiin lukee muokkaajan nimi, eli tässä tapauksessa Ilokaasu Laitoin nui dmesg tulosteet code tagien väliin jotta ne on selvemmät lukea ja mahtuu hieman paremmin näytölle

6

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 07.04.08 - klo:23.42 »

eli tässä vähän lisää tietoa malli on wli-u2-kg54-ai
Aika paljon löysin tietoa että muillakin on ongelmia ollut mutta mikään ei kyllä ratkaissut mun ongelmaa...
tässä tulosteita...itse en kyl tajua noist mitään joten apua todella kaivataan
ja vieläkin tuo siis tunnistaa cd levyksi tuon tikun


meme@meme:~$ lsusb
Bus 005 Device 001: ID 0000:0000  
Bus 003 Device 002: ID 046d:c518 Logitech, Inc.
Bus 003 Device 001: ID 0000:0000  
Bus 004 Device 001: ID 0000:0000  
Bus 002 Device 001: ID 0000:0000  
Bus 001 Device 001: ID 0000:0000  
meme@meme:~$





meme@meme:~$ lshw -c network
Hardware Lister (lshw) - B.02.10
usage: lshw [-format] [-options ...]
       lshw -version

        -version        print program version (B.02.10)

format can be
        -html           output hardware tree as HTML
        -xml            output hardware tree as XML
        -short          output hardware paths
        -businfo        output bus information

options can be
        -class CLASS    only show a certain class of hardware
        -C CLASS        same as '-class CLASS'
        -disable TEST   disable a test (like pci, isapnp, cpuid, etc. )
        -enable TEST    enable a test (like pci, isapnp, cpuid, etc. )
        -quiet          don't display status

7

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 07.04.08 - klo:01.48 »

heti tuli parempi mieli....
 
odotellaan rauhassa vastausta, mutta kyllä silti alkuperäistä viestiäni on lyhennetty

8

Laitealue / Vs: langattoman verkon asennus buffalo usb palikalla

« : 07.04.08 - klo:01.26 »

Ja ennenkuin mitään vastausta ehtii saamaan on ylläpito näköjään poistanut puolet kirjoituksestani niin ettei kokonaisuutta saa edes selville. Enkä edes haukkunut pahasti.... Että sellaista sensuuria. Tämäkö on sitten sitä AVOINTA lähdekoodia?

9

Laitealue / langattoman verkon asennus buffalo usb palikalla

« : 06.04.08 - klo:23.52 »

Asensin sitten vihdoin ja viimein ja synaptic ei suostunut enää käynnistymään. Monen tuskaisen tunnin jälkeen päätin laittaa koko asennuksen jälleen uusiksi! Hip hip hurraa!! Tällä kertaa synaptic taas toimi ja sain asennettua tämän ohjelman jolla windowsin ajureita voi asentaa. Nyt kuitenkin kun laitan usb palikan paikallaan niin linux tunnistaa sen cd levyksi!!! Ja kun asentaa windowsin ajurin niin ilmoittaa että invalid driver. Langattomia verkkoja ei tietenkään näy kun sellaista palikkaa ei ole millä se ne tunnistaisi!!!

No,,, tekis mieli valittaa että tää linux on ihan P%¤#% mutta jätetään väliin ja toivotaan apua jotta saisin tämän toimimaan! Kiitoksia ja etukäteen YKSINKERTAISISTA vastauksista