1
Ohjelmointi, palvelimet ja muu edistyneempi käyttö / Leffat talteen
« : 15.10.18 - klo:20.16 »
.
Ubuntu 24.04 LTS | Lataa ja asenna | Tutustu yhteisöön | Blogi | Yritysten tarjoamat palvelut
Uusimmat julkaisut: 24.04 LTS (suositeltu, 25.4.2024) ja 23.10 (16.10.2023).
Tässä osiossa voit tarkastella kaikkia tämän jäsenen viestejä. Huomaa, että näet viestit vain niiltä alueilta, joihin sinulla on pääsy.
sudo lshw -class network
antaa seuraavaa:*-network
description: Network controller
product: BCM43224 802.11a/b/g/n
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:08:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list
configuration: driver=bcma-pci-bridge latency=0
resources: irq:16 memory:e8000000-e8003fff
*-network DISABLED
description: Ethernet interface
product: 88E8072 PCI-E Gigabit Ethernet Controller
vendor: Marvell Technology Group Ltd.
physical id: 0
bus info: pci@0000:20:00.0
logical name: eth0
version: 10
serial:
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 latency=0 link=no multicast=yes port=twisted pair
resources: irq:44 memory:e0000000-e0003fff ioport:2000(size=256) memory:3fc00000-3fc1ffff
*-network DISABLED
description: Wireless interface
physical id: 1
logical name: wlan0
serial:
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=brcmsmac driverversion=3.8.0-19-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11abgn
I am running Ubuntu 11.10. I have had problems with Unity in that often the 'menu' to the left does not pop up when I mouse over it so have reverted to running Gnome 3. All seems fine so far.
When I insert and Audio CD Banshee is automatically executed. I can use the settings to change the program which runs when I insert a CD but can only select from 'installed' programs. I would like to be able to run a script, specifically abcde for ripping CDs. But, I cannot find a way of specifying this.
Searching the web throws up lots of information on how to do it in older versions which seemed to have an 'execute this command' option. gnome 3 does not seem to have this.
Any ideas about how to achieve this?
Thanks,
Andrew
066f:4200 SigmaTel, Inc. STIr4200 IrDA Bridge
[73603.988174] usb 5-2: new full speed USB device using uhci_hcd and address 5
[73604.112107] usb 5-2: device descriptor read/64, error -71
[73604.384422] SigmaTel STIr4200 IRDA/USB found at address 5, Vendor: 66f, Product: 4200
[73604.388258] stir4200 5-2:1.0: IrDA: Registered SigmaTel device irda0
sudo lshw
Kertoo ajuriksi: