SMART testejä en saa menemään läpi, kun tulee tuo read failure vastaan. Kuinka saan reallocoitua tuon blockin?
Saisin vähän paremmin varmuutta, että onko levyllä vain yksittäinen bad block vai onko koko levy laukeamassa. Tietysti olisi myös kiva tietää, että mikä tiedosto tuolla sijaitsee.
Ubuntu 12.04
RAID5
LVM2
XFS
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 20% 17859 684609913
# 2 Extended offline Completed: read failure 90% 17843 684609913
# 3 Short offline Completed: read failure 20% 17843 684609913
# 4 Extended offline Aborted by host 90% 17750 -
# 5 Extended offline Aborted by host 90% 17750 -
Disk /dev/sda: 1500.3 GB, 1500301910016 bytes
255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sda1 63 2930272064 1465136001 fd Linux raid autodetect
Kaikki SMART tiedot:
sudo smartctl -a /dev/sda
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.2.0-24-generic-pae] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F2 EG
Device Model: SAMSUNG HD154UI
Firmware Version: 1AG01118
User Capacity: 1,500,301,910,016 bytes [1.50 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Mon Sep 3 09:49:05 2012 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 114) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (19602) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 34) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 096 051 Pre-fail Always - 192
3 Spin_Up_Time 0x0007 072 072 011 Pre-fail Always - 9240
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 63
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 13510
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 17861
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 63
13 Read_Soft_Error_Rate 0x000e 100 096 000 Old_age Always - 191
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 2
184 End-to-End_Error 0x0033 100 100 000 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 1049
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 068 044 000 Old_age Always - 32 (Min/Max 28/32)
194 Temperature_Celsius 0x0022 067 043 000 Old_age Always - 33 (0 33 33 28)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1595585
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 099 000 Old_age Always - 20
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 11 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 11 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 0d 34 a5 e7 Error: UNC at LBA = 0x07a5340d = 128267277
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 07 34 a5 e7 08 9d+10:50:03.600 READ DMA
ec 00 00 00 00 00 a0 08 9d+10:50:03.570 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 9d+10:50:03.570 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 9d+10:50:03.570 IDENTIFY DEVICE
Error 10 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 0d 34 a5 e7 Error: UNC at LBA = 0x07a5340d = 128267277
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 07 34 a5 e7 08 9d+10:50:01.830 READ DMA
c8 00 08 ff 33 a5 e7 08 9d+10:50:01.830 READ DMA
c8 00 08 f7 33 a5 e7 08 9d+10:50:01.830 READ DMA
c8 00 08 ef 33 a5 e7 08 9d+10:50:01.830 READ DMA
Error 9 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 c1 e4 d9 e1 Error: UNC at LBA = 0x01d9e4c1 = 31057089
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 bf e4 d9 e1 08 9d+09:42:19.080 READ DMA
ec 00 00 00 00 00 a0 08 9d+09:42:19.060 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 9d+09:42:19.060 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 9d+09:42:19.050 IDENTIFY DEVICE
Error 8 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 c1 e4 d9 e1 Error: UNC at LBA = 0x01d9e4c1 = 31057089
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 bf e4 d9 e1 08 9d+09:42:16.020 READ DMA
ec 00 00 00 00 00 a0 08 9d+09:42:16.000 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 9d+09:42:16.000 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 9d+09:42:15.970 IDENTIFY DEVICE
Error 7 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 c5 e4 d9 e1 Error: UNC at LBA = 0x01d9e4c5 = 31057093
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 bf e4 d9 e1 08 9d+09:42:12.220 READ DMA
c8 00 08 b7 e4 d9 e1 08 9d+09:42:12.220 READ DMA
c8 00 08 af e4 d9 e1 08 9d+09:42:12.220 READ DMA
c8 00 08 a7 e4 d9 e1 08 9d+09:42:12.220 READ DMA
c8 00 08 9f e4 d9 e1 08 9d+09:42:12.220 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 20% 17859 684609913
# 2 Extended offline Completed: read failure 90% 17843 684609913
# 3 Short offline Completed: read failure 20% 17843 684609913
# 4 Extended offline Aborted by host 90% 17750 -
# 5 Extended offline Aborted by host 90% 17750 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Aihe: SMART:n ilmoittaman Bad blockin ottaminen kiintolevyltä pois käytöstä? (Luettu 2666 kertaa)
