Kun on noi rauta-asiat(kin) huonosti hallussa niin pyydän tulkintaa. Tuossa on alla tulsotusta läppäristäni, johon yritän anyseetä nyt panna. Pöytäkoneeseen onnistuin, mutta tämä läpyskä, jossa sitä varsinaisesti tarvittaisiin, ei toimi anyseen kanssa. Jotenkin samaan tapaan yritin molempiin masiinoihin asettaa. Fyysisesti koneessa on 2 usb töpselireikää. Tulkitsen tuosta alla olevasta, että masiinasta löytyisi kaikkiaan 4, ja että nopeutta ei ole kuin tuo pienempi. Menikö oikein? Ja että löytyiskö vauhtia lisää jollakin biosin päivityksellä, jos se osaisi/uskaltaisi tehdä? Muutamitä? Aurinkokaan ei paista.
HP compaq nx9005
@expee:~$ lspci
00:00.0 Host bridge: ATI Technologies Inc AGP Bridge [IGP 320M] (rev 13)
00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 320M] (rev 01)
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+]
00:08.0 Modem: ALi Corporation M5457 AC'97 Modem Controller
00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 01)
00:0a.1 CardBus bridge: O2 Micro, Inc. OZ6933/711E1 CardBus/SmartCardBus Controller (rev 01)
00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4)
00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility U1
@expee:~$ dmesg |grep -i hci
[ 28.117694] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 28.118170] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 28.118705] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 28.118731] ohci_hcd 0000:00:02.0: irq 10, io mem 0xd0004000
[ 28.331680] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[d0007000-d00077ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 28.600762] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 29.147734] usb 1-2: new full speed USB device using ohci_hcd and address 3
[ 46.404399] usb 1-1: reset full speed USB device using ohci_hcd and address 2
[ 67.795121] Bluetooth: HCI device and connection manager initialized
[ 67.795128] Bluetooth: HCI socket layer initialized
@expee:~$ dmesg|grep usb
[ 28.094642] usbcore: registered new interface driver usbfs
[ 28.094681] usbcore: registered new interface driver hub
[ 28.107525] usbcore: registered new device driver usb
[ 28.177726] usb usb1: configuration #1 chosen from 1 choice
[ 28.600762] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 28.839401] usb 1-1: configuration #1 chosen from 1 choice
[ 29.147734] usb 1-2: new full speed USB device using ohci_hcd and address 3
[ 29.372324] usb 1-2: configuration #1 chosen from 1 choice
[ 46.109139] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
[ 46.109212] dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter)
[ 46.109247] dvb-usb: Anysee DVB USB2.0 error while loading driver (-19)
[ 46.109270] usbcore: registered new interface driver dvb_usb_anysee
[ 46.404399] usb 1-1: reset full speed USB device using ohci_hcd and address 2
[ 46.639103] usbcore: registered new interface driver zd1211rw
