Hei!
Olen harrastanut tätä ubuntua(5.04 - hoary - pc) noin viikon ja otsikon mukaisia ongelmia.
lspci:
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] System Controller (rev 14)
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] AGP Bridge
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50)
0000:00:0a.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 86)
0000:01:05.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 MX 440] (rev a3)
dmesg:
Linux version 2.6.10-5-386 (buildd@terranova) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #1 Mon Oct 10 11:15:41 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f51a0
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 GBT ) @ 0x000f6a60
ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff5d40
ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hdb2 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1475.023 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 511772k/524224k available (1437k kernel code, 11860k reserved, 753k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2924.54 BogoMIPS (lpj=1462272)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000
CPU: AMD Athlon(tm) XP 1700+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4300k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfa2c0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
audit: initializing netlink socket (disabled)
audit(1129728299.932:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Enabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
PCI0 USB0 USB1 UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4300KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (32 C)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: SAMSUNG SP4002H, ATA DISK drive
hdb: Maxtor 4D040H2, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p4 < p5 p6 p7 p8 p9 p10 p11 >
hdb: max request size: 1024KiB
hdb: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(33)
hdb: cache flushes not supported
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3 < p5 >
Probing IDE interface ide1...
hdc: LITE-ON LTR-40125S, ATAPI CD/DVD-ROM drive
hdd: LITEON DVD-ROM LTD163, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Stopping tasks: ==|
Freeing memory... done (458 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 1510068k swap on /dev/hdb5. Priority:-1 extents:1
EXT3 FS on hdb2, internal journal
hdc: ATAPI 48X CD-ROM CD-R/RW drive, 1984kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
parport_pc: VIA parallel port: io=0x378, irq=7
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AMD 761 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 11, io base 0xd800
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:07.3: irq 11, io base 0xdc00
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:07.2: Unlink after no-IRQ? Different ACPI or APIC settings may help.
usb 1-1: khubd timed out on ep0in
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:07.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:07.5 to 64
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: VIA Rhine III at 0xec00, 00:0f:3d:cd:ba:f3, IRQ 18.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NET: Registered protocol family 17
usb 1-1: khubd timed out on ep0out
usb 1-1: khubd timed out on ep0out
usb 1-1: device not accepting address 2, error -110
usb 1-1: new full speed USB device using uhci_hcd and address 3
usb 1-1: khubd timed out on ep0in
usb 1-1: khubd timed out on ep0out
usb 1-1: khubd timed out on ep0out
usb 1-1: device not accepting address 3, error -110
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
eth0: no IPv6 routers present
irq 11: nobody cared (try booting with the "irqpoll" option.
[<c012e4cb>] __report_bad_irq+0x31/0x77
[<c012e59e>] note_interrupt+0x75/0x9b
[<c012df82>] __do_IRQ+0xd3/0x111
[<c0104cc5>] do_IRQ+0x19/0x24
[<c0103966>] common_interrupt+0x1a/0x20
[<c010101c>] default_idle+0x0/0x29
[<c010103f>] default_idle+0x23/0x29
[<c0101095>] cpu_idle+0x21/0x45
[<c03266a4>] start_kernel+0x16f/0x173
handlers:
[<e0a5c671>] (usb_hcd_irq+0x0/0x4e [usbcore])
[<e0a5c671>] (usb_hcd_irq+0x0/0x4e [usbcore])
Disabling IRQ #11
usb 1-2: new full speed USB device using uhci_hcd and address 4
usb 1-2: khubd timed out on ep0in
usb 1-2: khubd timed out on ep0out
usb 1-2: khubd timed out on ep0out
usb 1-2: device not accepting address 4, error -110
usb 1-2: new full speed USB device using uhci_hcd and address 5
usb 1-2: khubd timed out on ep0in
usb 1-2: khubd timed out on ep0out
usb 1-2: khubd timed out on ep0out
usb 1-2: device not accepting address 5, error -110
usb 1-2: new full speed USB device using uhci_hcd and address 6
usb 1-2: khubd timed out on ep0in
usb 1-2: khubd timed out on ep0out
usb 1-2: khubd timed out on ep0out
usb 1-2: device not accepting address 6, error -110
usb 1-2: new full speed USB device using uhci_hcd and address 7
usb 1-2: khubd timed out on ep0in
usb 1-2: khubd timed out on ep0out
usb 1-2: khubd timed out on ep0out
usb 1-2: device not accepting address 7, error -110
usb 1-1: new full speed USB device using uhci_hcd and address 8
usb 1-1: khubd timed out on ep0in
usb 1-1: khubd timed out on ep0out
usb 1-1: khubd timed out on ep0out
usb 1-1: device not accepting address 8, error -110
usb 1-1: new full speed USB device using uhci_hcd and address 9
usb 1-1: khubd timed out on ep0in
usb 1-1: khubd timed out on ep0out
usb 1-1: khubd timed out on ep0out
usb 1-1: device not accepting address 9, error -110
usb 1-2: new full speed USB device using uhci_hcd and address 10
usb 1-2: khubd timed out on ep0in
usb 1-2: khubd timed out on ep0out
usb 1-2: khubd timed out on ep0out
usb 1-2: device not accepting address 10, error -110
usb 1-2: new full speed USB device using uhci_hcd and address 11
usb 1-2: khubd timed out on ep0in
usb 1-2: khubd timed out on ep0out
usb 1-2: khubd timed out on ep0out
usb 1-2: device not accepting address 11, error -110
usb 1-1: new full speed USB device using uhci_hcd and address 12
usb 1-1: khubd timed out on ep0in
usb 1-1: khubd timed out on ep0out
usb 1-1: khubd timed out on ep0out
usb 1-1: device not accepting address 12, error -110
usb 1-1: new full speed USB device using uhci_hcd and address 13
usb 1-1: khubd timed out on ep0in
usb 1-1: khubd timed out on ep0out
usb 1-1: khubd timed out on ep0out
usb 1-1: device not accepting address 13, error -110
Liitän vielä fstabin:
# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
/dev/hdb2 / ext3 defaults,errors=remount-ro 0 1
/dev/hdb5 none swap sw 0 0
/dev/hdd /media/cdrom0 udf,iso9660 ro,user,noauto 0 0
/dev/hdc /media/cdrom1 udf,iso9660 ro,user,noauto 0 0
/dev/fd0 /media/floppy0 auto rw,user,noauto 0 0
/dev/hda9 /mnt/home ext3 defaults 1 2
/dev/hda10 /mnt/tmp ext3 defaults 1 2
/proc /proc/bus/usb usbfs defaults,user 0 0
ja /proc/bus/usb:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10-5-386 uhci_hcd
S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
S: SerialNumber=0000:00:07.3
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10-5-386 uhci_hcd
S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
1. Osaako joku neuvoa miten nuo monitoimilaite Epson Stylus CX3650 ja kamera Powershot A70 saadaan näkymään koneessa?
mandrakella onnistuin vajaa vuosi sitten asentamaan monitoimilaitteen mutta siellä on tää rpm ja käsitän sen vielä toistaiseksi paremmin. Tämä deb on mulle vielä outo.
2. Mulla on toisella kovalevyllä(hda) mandrake 10 ja olen saanut nuo linuxit liitettyä niin että näen toisen /home ja /tmp hakemistot. Saan ne siirrettyä esim. jos olen ubuntussa niin mandraken -> ubuntun kovalevylle mutta miten saisin ne siirrettyä takaisin? Onko kyse käyttöoikeuksista ja miten ne kierretään?
3. Lisään vielä mandraken fstabin kunhan käyn sillä puolen. Onko kaikki siinä kunnossa? Mitä pitäisi poistaa tai muuttaa?thx etukäteen.
Aihe: epson stylus cx3650, kamera canon powershot a70, usb-laitteiden ongelmia. (Luettu 6587 kertaa)
