Aluks mulla ei ollu asennettuna firestarter:ia.. ilmeisesti palomuuri ei ollu päällä? Kun ei toiminut niin asensin ton ja kokeilin laittaa sallituksi kaiken liikenteen toiselta koneelta jolta yritin käyttää live webkameraa nettiselaimella..
ei vaan saa yhteyttä?
![Huh ???](https://forum.ubuntu-fi.org/Smileys/default/huh.gif)
Motionissa on tälläset asetukset:
# daemon = off
# setup_mode = off
# videodevice = /dev/video0
# input = 8
# norm = 0
# frequency = 0
# rotate = 0
# width = 320
# height = 240
# framerate = 25
# netcam_url = (null)
# netcam_userpass = (null)
# netcam_proxy = (null)
# auto_brightness = off
# brightness = 0
# contrast = 0
# saturation = 0
# hue = 0
# roundrobin_frames = 1
# roundrobin_skip = 1
# switchfilter = off
# threshold = 1500
# threshold_tune = off
# noise_level = 32
# noise_tune = on
# night_compensate = off
# despeckle = (null)
# mask_file = (null)
# smart_mask_speed = 0
# lightswitch = 0
# minimum_motion_frames = 1
# pre_capture = 0
# post_capture = 0
# gap = 60
# minimum_gap = 0
# max_mpeg_time = 3600
# low_cpu = 0
# output_all = off
# output_normal = on
# output_motion = off
# quality = 85
# ppm = off
# ffmpeg_cap_new = on
# ffmpeg_cap_motion = on
# ffmpeg_timelapse = 0
# ffmpeg_timelapse_mode = daily
# ffmpeg_bps = 100000
# ffmpeg_variable_bitrate = 0
# ffmpeg_video_codec = msmpeg4
# snapshot_interval = 0
# locate = off
# text_right = %Y-%m-%d\n%T
# text_left = (null)
# text_changes = off
# text_double = off
# target_dir = /tmp
# snapshot_filename = %v-%Y%m%d%H-snapshot
# jpeg_filename = %Y%m%d%H
# ffmpeg_filename = %Y%m%d
# timelapse_filename = %Y%m%d-timelapse
# webcam_port = 8081
# webcam_quality = 50
# webcam_motion = off
# webcam_maxrate = 8
# webcam_localhost = off
# webcam_limit = 0
# control_port = 8080
# control_localhost = on
# control_html_output = on
# control_authentication = (null)
# track_type = 0
# track_port = (null)
# track_motorx = 0
# track_maxx = 0
# track_iomojo_id = 0
# track_speed = 255
# track_stepsize = 40
# quiet = on
# on_event_start = (null)
# on_event_end = (null)
# on_picture_save = (null)
# on_motion_detected = (null)
# on_movie_start = (null)
# on_movie_end = (null)
# sql_log_image = on
# sql_log_snapshot = on
# sql_log_mpeg = off
# sql_log_timelapse = off
# mysql_db = (null)
# mysql_host = (null)
# mysql_user = (null)
# mysql_password = (null)
# pgsql_db = (null)
# pgsql_host = (null)
# pgsql_user = (null)
# pgsql_password = (null)
# pgsql_port = 5432
# video_pipe = (null)
# motion_video_pipe = (null)
# thread = (null)
ja tiedostossa /etc/motion/motion.conf:
# Minimal motion example config file provided by the
# Debian motion package - for basic webcam operation.
#
# You most certainly want to investigate
# /usr/share/doc/motion/examples/motion-dist.conf.gz
# for further configuration options. Also, refer to the
# motion man page and /usr/share/doc/motion/motion_guide.html
# for detailed information on configuration options.
daemon off
quiet on
# You may very well need to change this (check with 'dmesg'
# after plugging in your webcam)
videodevice /dev/video0
# Image size in pixels (valid range is camera dependent)
width 320
height 240
framerate 25
quality 85
auto_brightness off
# Initial brightness, contrast, hue (NTSC), and saturation
# 0 = disabled (valid range 0-255)
brightness 0
contrast 0
saturation 0
hue 0
# Encode movies in real-time (install ffmpeg before enabling)
ffmpeg_cap_new off
# Codec to be used by ffmpeg for the video compression.
# Supported formats: mpeg4, msmpeg4.
ffmpeg_video_codec msmpeg4
# Target base directory for pictures and films
# You should probably change this (create dir beforehand)
target_dir /tmp
# Define a port number (e.g. 8000) to enable the mini-http server
# 0 = disabled
webcam_port 8081
# Set to 'off' to allow anybody (not just localhost) to view the
# webcam via the mini-http server (
http://hostname:port)
webcam_localhost off
webcam_quality 50
webcam_maxrate 8
# TCP/IP port for the http server to listen on (default: 0 = disabled)
control_port 8080
# Restrict control connections to localhost only (default: on)
control_localhost on
# Output for http server, select off to choose raw text plain (default: on)
control_html_output on
# Authentication for the http based control. Syntax username:password
# Default: not defined (Disabled)
; control_authentication username:password