Kirjoittaja Aihe: Terminal ei toimi!!! (RATKAISTU)  (Luettu 2017 kertaa)

stempler

  • Käyttäjä
  • Viestejä: 17
    • Profiili
Terminal ei toimi!!! (RATKAISTU)
« : 24.07.07 - klo:22.29 »
Terminal jää hetkeksi Starting terminal tilaan ja sitten vain sammua plosahtaa...?
Millä saisin terminalin jälleen toimimaan?
Hätäpäissäni asentelin konsolen, mutta kun jotenkin tykkään vain enemmän terminalista  :o
« Viimeksi muokattu: 25.07.07 - klo:10.35 kirjoittanut stempler »

Stargazers

  • Käyttäjä
  • Viestejä: 549
    • Profiili
Vs: Terminal ei toimi!!!
« Vastaus #1 : 24.07.07 - klo:22.35 »
Käynnistä konsole (Jos se toimii) ja kirjoita siinä gnome-terminal & ja paina enter.
Sitten jos tulee virheitä, copy-pasteta ne tänne. Siitä voi olla helpompaa katsella mikä aiheuttaa moisen.

Vinkki: Mustaaminen riittää, sitten hiiren keskirullalla painamalla saa sen mustatun tekstin pastetettua.

stempler

  • Käyttäjä
  • Viestejä: 17
    • Profiili
Vs: Terminal ei toimi!!!
« Vastaus #2 : 24.07.07 - klo:22.46 »
xxxxxxxx@xxxxxxxi:~$ The program 'gnome-terminal' received an X Window System error.
This probably reflects a bug in the program.
The error was 'BadValue (integer parameter out of range for operation)'.
  (Details: serial 105 error_code 2 request_code 78 minor_code 0)
  (Note to programmers: normally, X errors are reported asynchronously;
   that is, you will receive the error a while after causing it.
   To debug your program, run it with the --sync command line
   option to change this behavior. You can then get a meaningful
   backtrace from your debugger if you break on the gdk_x_error() function.)

stempler

  • Käyttäjä
  • Viestejä: 17
    • Profiili
Vs: Terminal ei toimi!!!
« Vastaus #3 : 24.07.07 - klo:23.00 »
xxxxxxxx@xxxxxxxi:~$ The program 'gnome-terminal' received an X Window System error.
This probably reflects a bug in the program.
The error was 'BadValue (integer parameter out of range for operation)'.
  (Details: serial 105 error_code 2 request_code 78 minor_code 0)
  (Note to programmers: normally, X errors are reported asynchronously;
   that is, you will receive the error a while after causing it.
   To debug your program, run it with the --sync command line
   option to change this behavior. You can then get a meaningful
   backtrace from your debugger if you break on the gdk_x_error() function.)

Itse itseäni lainaten:

vika oli itseasiassa nvidian ajureissa.
alla tietoa bugista:
https://bugs.launchpad.net/ubuntu/+source/gnome-terminal/+bug/72956

ja korjaus oli ygp:ssä (yhden googlen päässä)
http://ubuntuforums.org/archive/index.php/t-392734.html

lyhyesti näin korjasin
sudo nvidia-xconfig --add-argb-glx-visuals ja sen jälkeen rebootti.

Kiitos kumminkin kaikille osallistuneille.

Stargazers

  • Käyttäjä
  • Viestejä: 549
    • Profiili
Vs: Terminal ei toimi!!!
« Vastaus #4 : 25.07.07 - klo:01.44 »
Hyvä juttu että selvisi :)