Ubuntu Suomen keskustelualueet
Ubuntun käyttö => Laitealue => Aiheen aloitti: Sami Mäntysaari - 04.11.15 - klo:01.14
-
Hei kaikille pitkästä aikaa,
Onkos tietoa mitenkäs saisi enemmän lämpötiloja ja/tai muuta tietoa ulos?
sensors:
acpitz-virtual-0
Adapter: Virtual device
temp1: +27.8°C (crit = +105.0°C)
temp2: +29.8°C (crit = +105.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +35.0°C (high = +80.0°C, crit = +100.0°C)
Core 0: +33.0°C (high = +80.0°C, crit = +100.0°C)
Core 1: +32.0°C (high = +80.0°C, crit = +100.0°C)
-
lm-sensors
-
lm-sensors
En ole noin tyhmä.
sm@Server:~$ sudo apt-get install lm-sensors:
[sudo] password for sm:
Reading package lists... Done
Building dependency tree
Reading state information... Done
lm-sensors is already the newest version.
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
sm@Server:~$ sudo sensors-detect:
# sensors-detect revision 6170 (2013-05-20 21:25:22 +0200)
# System: ASUS All Series
# Board: ASUSTeK COMPUTER INC. H81M-K
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): YES
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
AMD Family 12h and 14h thermal sensors... No
AMD Family 15h thermal sensors... No
AMD Family 15h power sensors... No
AMD Family 16h power sensors... No
Intel digital thermal sensor... Success!
(driver `coretemp')
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... Yes
Found `Nuvoton NCT5532D/NCT6779D Super IO Sensors' Success!
(address 0x290, driver `nct6775')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): YES
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): YES
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): YES
Using driver `i2c-i801' for device 0000:00:1f.3: Intel Lynx Point (PCH)
Module i2c-i801 loaded successfully.
Module i2c-dev loaded successfully.
Next adapter: i915 gmbus ssc (i2c-0)
Do you want to scan it? (yes/NO/selectively): YES
Next adapter: i915 gmbus vga (i2c-1)
Do you want to scan it? (yes/NO/selectively): YES
Next adapter: i915 gmbus panel (i2c-2)
Do you want to scan it? (yes/NO/selectively): YES
Next adapter: i915 gmbus dpc (i2c-3)
Do you want to scan it? (yes/NO/selectively): YES
Next adapter: i915 gmbus dpb (i2c-4)
Do you want to scan it? (yes/NO/selectively): YES
Next adapter: i915 gmbus dpd (i2c-5)
Do you want to scan it? (yes/NO/selectively): YES
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `nct6775':
* ISA bus, address 0x290
Chip `Nuvoton NCT5532D/NCT6779D Super IO Sensors' (confidence: 9)
Driver `coretemp':
* Chip `Intel digital thermal sensor' (confidence: 9)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
nct6775
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Do you want to add these lines automatically to /etc/modules? (yes/NO)YES
Successful!
Monitoring programs won't work until the needed modules are
loaded. You may want to run 'service kmod start'
to load them.
Unloading i2c-dev... OK
Unloading i2c-i801... OK
Unloading cpuid... OK
Manuaalisesti modprobed nämä:
modprobe coretemp
modprobe nct6775
sm@Server:~$ lsmod:
Module Size Used by
nct6775 55222 0
hwmon_vid 12783 1 nct6775
nfnetlink 14606 0
bluetooth 391136 0
eeepc_wmi 13151 0
asus_wmi 24191 1 eeepc_wmi
sparse_keymap 13948 1 asus_wmi
x86_pkg_temp_thermal 14205 0
intel_powerclamp 14705 0
coretemp 13435 0
kvm 455843 0
crct10dif_pclmul 14289 0
crc32_pclmul 13113 0
ghash_clmulni_intel 13216 0
aesni_intel 55624 0
aes_x86_64 17131 1 aesni_intel
lrw 13286 1 aesni_intel
gf128mul 14951 1 lrw
glue_helper 13990 1 aesni_intel
ablk_helper 13597 1 aesni_intel
cryptd 20359 3 ghash_clmulni_intel,aesni_intel,ablk_helper
snd_hda_codec_realtek 65812 1
serio_raw 13462 0
lpc_ich 21080 0
i915 788212 1
mac_hid 13205 0
snd_hda_intel 56531 0
snd_hda_codec 193017 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 13602 1 snd_hda_codec
snd_pcm 102099 2 snd_hda_codec,snd_hda_intel
video 19476 2 i915,asus_wmi
drm_kms_helper 55071 1 i915
snd_page_alloc 18710 2 snd_pcm,snd_hda_intel
wmi 19177 1 asus_wmi
snd_timer 29482 1 snd_pcm
snd 69322 6 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_pcm,snd_hda_codec,snd_hda_intel
mei_me 18627 0
mei 82276 1 mei_me
soundcore 12680 1 snd
drm 303102 2 i915,drm_kms_helper
shpchp 37032 0
i2c_algo_bit 13413 1 i915
lp 17759 0
parport 42348 1 lp
ahci 34091 3
psmouse 106692 0
r8169 71677 0
libahci 32716 1 ahci
mii 13934 1 r8169
Viimeinen tulos:
sm@Server:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +27.8°C (crit = +105.0°C)
temp2: +29.8°C (crit = +105.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +34.0°C (high = +80.0°C, crit = +100.0°C)
Core 0: +34.0°C (high = +80.0°C, crit = +100.0°C)
Core 1: +32.0°C (high = +80.0°C, crit = +100.0°C)
nct6779-isa-0290
Adapter: ISA adapter
in0: +0.87 V (min = +0.00 V, max = +1.74 V)
in1: +1.03 V (min = +0.00 V, max = +0.00 V) ALARM
in2: +3.36 V (min = +0.00 V, max = +0.00 V) ALARM
in3: +3.34 V (min = +0.00 V, max = +0.00 V) ALARM
in4: +1.00 V (min = +0.00 V, max = +0.00 V) ALARM
in5: +0.00 V (min = +0.00 V, max = +0.00 V)
in6: +0.65 V (min = +0.00 V, max = +0.00 V) ALARM
in7: +3.39 V (min = +0.00 V, max = +0.00 V) ALARM
in8: +3.28 V (min = +0.00 V, max = +0.00 V) ALARM
in9: +1.01 V (min = +0.00 V, max = +0.00 V) ALARM
in10: +0.15 V (min = +0.00 V, max = +0.00 V) ALARM
in11: +0.13 V (min = +0.00 V, max = +0.00 V) ALARM
in12: +0.13 V (min = +0.00 V, max = +0.00 V) ALARM
in13: +0.13 V (min = +0.00 V, max = +0.00 V) ALARM
in14: +0.14 V (min = +0.00 V, max = +0.00 V) ALARM
fan1: 915 RPM (min = 0 RPM)
fan2: 1004 RPM (min = 0 RPM)
SYSTIN: +117.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = thermistor
CPUTIN: +35.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor
AUXTIN0: +46.0°C sensor = thermistor
AUXTIN1: +109.0°C sensor = thermistor
AUXTIN2: +108.0°C sensor = thermistor
AUXTIN3: +17.0°C sensor = thermal diode
PECI Agent 0: +34.0°C
PCH_CHIP_CPU_MAX_TEMP: +0.0°C
PCH_CHIP_TEMP: +0.0°C
PCH_CPU_TEMP: +0.0°C
intrusion0: ALARM
intrusion1: ALARM
beep_enable: disabled
(Ei ollut aktivoinut noita ajureita.)
-
(Ei ollut aktivoinut noita ajureita.)
Juu, sensors-detect pitää ajaa itse, että saa kaikki lähteet tunnistettua ja lisättyä tarvittavat moduulit automaattisesti ladattaviksi. Nämä sensoriajurit eivät toimi täysin automaagisesti.
-
(Ei ollut aktivoinut noita ajureita.)
Juu, sensors-detect pitää ajaa itse, että saa kaikki lähteet tunnistettua ja lisättyä tarvittavat moduulit automaattisesti ladattaviksi. Nämä sensoriajurit eivät toimi täysin automaagisesti.
Olin aikaisemmin sen ajanutkin, mutta en ollut muistanut ladata niitä. Oops.