Ubuntu Suomen keskustelualueet
Ubuntun käyttö => Asentaminen ja käyttöönotto => Aiheen aloitti: UbuntuBoi - 01.05.07 - klo:01.29
-
Miten säädän monitorista hertzejä manuaalisesti, jostain syystä ei anna kun maksimissa 74hertziä vaikka todellisuudessa pitäis antaa 150hertsiä resoilla mitä käytän..
tiedossa on kaikki monitorin alkuperäiset asetukset..
onkohan nyt näin ettei linuxi tunnista kunnolla tätä minun monitoria
monitori on:
Fujitsu x177a
Synkronointi:
vaakataajuus: 31 - 92hz
pystytaajuus: 50 - 150hz
Tämänhetken asetukset:
Resoluutio: 1024x768 ( Pitäis antaa 100hz mutta maksimi nyt 75 (repee silmat paasta noilla hertseilla)
vaakataajuus: 60hz
pystytaajuus: 75hz
Voisko joku neuvoa tarkemmin, koska olen noob ja viimeksi jouduin instaamaan koko linuxin uudestaan =)
-
Muuta xorg.confiin käsin etsimällä kohta:
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 31.0 - 92.0
VertRefresh 50.0 - 150.0
ja muuta vaakataajuus (HorizSync) ja pystytaajuus (VertRefresh) vastaamaan monitorin arvoja. Suosittelen backupin tekoa xorg.confista ennen muutostöitä.
Nyt pitäisi olla saatavana oikeat virkistystaajuudet.
-
Juups meni taas vaihteeks koko linux sekasin, tulee alussa blue screen ja jotain xserverista apinoi
eli muuin pelkastaan sita Xorg.conf ohjeiden mukasesti sekos koko romu
korvasin muokatun Xorg.conf omalla backupilla * xorg.conf *
pitaako se koko X11 kansiosta ottaa Backup
Section "Files"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/100dpi"
FontPath "/usr/share/fonts/X11/75dpi"
# path to defoma fonts
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection
Section "Module"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "Device"
Identifier "nVidia Corporation G71 [GeForce 7300 GS]"
Driver "nv"
BusID "PCI:1:0:0"
EndSection
Section "Monitor"
Identifier "FUJITSU x177"
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "nVidia Corporation G71 [GeForce 7300 GS]"
Monitor "FUJITSU x177"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "1600x1200" "1280x1024" "1024x768" "832x624" "800x600" "720x400" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1600x1200" "1280x1024" "1024x768" "832x624" "800x600" "720x400" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1600x1200" "1280x1024" "1024x768" "832x624" "800x600" "720x400" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1600x1200" "1280x1024" "1024x768" "832x624" "800x600" "720x400" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1600x1200" "1280x1024" "1024x768" "832x624" "800x600" "720x400" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1600x1200" "1280x1024" "1024x768" "832x624" "800x600" "720x400" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
EndSection
Section "DRI"
Mode 0666
EndSection
Taman
Section "Monitor"
Identifier "FUJITSU x177"
Option "DPMS"
EndSection
korvasin talla
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 31.0 - 92.0
VertRefresh 50.0 - 150.0
ei lahde linuks paalle, vaikka vaihdoin vakioksi sen xorg.conf
Nyt livecd tilassa......
Odottelen jos joku keksis vastauksen ettei taas joutuis asentaan linuxia uudestaan
-
Taman
Section "Monitor"
Identifier "FUJITSU x177"
Option "DPMS"
EndSection
korvasin talla
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 31.0 - 92.0
VertRefresh 50.0 - 150.0
Kokeilepa korvaavana ehdottamasi sijaan tätä:
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 31.0 - 92.0
VertRefresh 50.0 - 150.0
EndSection
Eli näyttää siltä, että sinulta on jäänyt tuo "EndSection" pois korvaavasta versiosta.
-
juu oli se naemma siella en vaan ollu hoksannu pistaa ihan loppuun koodia.
ei toimi noi vakio asetuksetkaan enaan, vois alkaa uudestaan instaan vaihteeksi
-
ei toimi noi vakio asetuksetkaan enaan, vois alkaa uudestaan instaan vaihteeksi
Jotain vikaa jossain on syvemmällä kuin xorg.conf-tiedostossa, jos varmuuskopion palauttaminenkaan ei enää saa X-ympäristöä käyntiin. Voisit kuitenkin kokeilla vielä käynnistystä safe mode -tilaan (grubin valikosta valitsemalla siis) ja koettaa loitsua sudo dpkg-reconfigure -phigh xserver-xorg
-
Suuuret kiitokset oli kyllä todella hieno loitsu ;)
nyt lähti peuhaamaan, hienoa ! =)
-
Juups pisti boottia niin vaihtu taas hertsit 75....
kiva ku tulee itelle aina semmoset ongelmat mitä ei voi korjata mitenkään =D
-
Taman
Section "Monitor"
Identifier "FUJITSU x177"
Option "DPMS"
EndSection
korvasin talla
Section "Monitor"
Identifier "Generic Monitor"
HorizSync 31.0 - 92.0
VertRefresh 50.0 - 150.0
ei lahde linuks paalle, vaikka vaihdoin vakioksi sen xorg.conf
No ongelmahan on siinä, että vaihdoit samalla tuon monitorin nimen, kun taas muualla samassa tiedostossa viitataan näyttöön edelleen vanhalla nimellä.. Eli älä muuta koko "Monitor"-kohtaa, ainoastaan nuo virkistystaajuudet:
Section "Monitor"
Identifier "FUJITSU x177"
Option "DPMS"
HorizSync 31.0 - 92.0
VertRefresh 50.0 - 150.0
EndSection
-
Jostain syystä näissä uudemmissa X.orgeissa ei näytä riitävän pelkkä xorg.confin muokkaaminen että saa näytön toimimaan oikein vaan joutuu tekemään "sudo dpkg-reconfigure -phigh xserver-xorg" Suse 10.2 kun kokeili joutui myös muokkaamaan näytön arvot sen omalla ohjelmalla.
-
Pitää pari päivää mietiskella tai uskallanko tosissaan vaihtaa noi asetukset ?? ja sitten ajaa ton
sudo dpkg-reconfigure -phigh xserver-xorg"
tullut kammo kun tais olla nyt 3kerta ku asensin ubuntun uudestaan ton takia =)))))
-
Juu se kysymys litania on hieman sellainen et tuli epävarma olo vastasiko oikein. Mut laitoin mitä se ehdotti ja näytön arvoiksi mitä valnistaja antaa. Sen jälkeen työpöytä tehosteet ei toiminut ihan oikein mutta ratkaisin sen asentamalla Berylin http://www.ubuntugeek.com/how-to-install-beryl-with-latest-nvidia-drivers-in-ubuntu-feisty-fawn.html tolla sivulla olevan ohjeen mukaan(beryl-manager jäi asentumatta mutta asensin sen synapticilla) Nyt toiminut ok viikon verran :)
xorg.conf näyttää tältä
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder3) Thu Nov 9 17:55:20 PST 2006
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf(5) manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen" 0 0
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
EndSection
Section "Files"
# path to defoma fonts
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/100dpi"
FontPath "/usr/share/fonts/X11/75dpi"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection
Section "Module"
Load "bitmap"
Load "ddc"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "v4l"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "fi"
Option "XkbOptions" "lv3:ralt_switch"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Identifier "stylus"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Identifier "eraser"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Identifier "cursor"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "Monitor"
Identifier "Tyypillinen näyttö"
HorizSync 30.0 - 82.0
VertRefresh 56.0 - 75.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Tyypillinen näytönohjain"
Driver "nvidia"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "Tyypillinen näytönohjain"
Monitor "Tyypillinen näyttö"
DefaultDepth 24
Option "UseFBDev" "true"
Option "AddARGBGLXVisuals" "True"
SubSection "Display"
Depth 1
Modes "1440x900" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1440x900" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1440x900" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1440x900" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1440x900" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1440x900" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
Näyttö Fujitsun SCALEOWIEW L19-1W ja toimii nyt 75Hz 1400x900 niinkuin pitääkin. Just tosin katsoin työpöydältä näytön tarkkuutta ja siellä luki vain 50Hz ja enimmän asetuksen olevan 55hz. mutta näytön menu ja omat silmäni kertovat sen kuitenkin olevan tuo 75Hz :)
-
joo kyllä on outoa nyt 52hertsiä ja silmät kyllä sanoo että 100hz kuin myös sinunkin silmäsi juha ;) ja samoten myös näytön menu 100hz ? =))
hyvä että mainitsit näytön omista asetuksista, ite just vilkasin niin oli 82hz ja ubuntu säädössä 72hz
ja asetuksilla käyttis 52hz niin näytössä tällöin 100hz