Kirjoittaja Aihe: Ubuntu 8.10 Realtek ALC880 asennusongelmat, äänet toimii nyt!  (Luettu 4104 kertaa)

luisfigo

  • Käyttäjä
  • Viestejä: 42
    • Profiili
Ubuntu 8.10 on käyttiksenä. Ja Realtek ALC880-äänipiirin asennus ei ota toimiakseen. 8.04 Ubuntulla sama ongelma.
Miten saisin äänet kuuluviin?

Olen ihan n00b tämän linuxin kanssa ja muuten olen tykännyt tästä mutta äänien toimimattomuuden takia vaihtuu kohta taas Vistaan takaisin :-\
« Viimeksi muokattu: 25.10.08 - klo:18.18 kirjoittanut luisfigo »

timsku

  • Käyttäjä
  • Viestejä: 225
    • Profiili
Onko kyseessä mikä emolevy/läppäri ? Kyseessä on siis ihan uusi asennus eikä mikään laitteistopäivityksestä johtuva ongelma ? Miten ongelma ilmenee, onko mitään ääniä tai herjaako jotain ? Mitä olen seurannut, yllättävän monella on pelkästään mixerin säädöt pielessä...
Seuraavien käskyjen tulosteet konsolista saattaisivat auttaa:
Koodia: [Valitse]
cat /etc/modprobe.d/alsa-base

Koodia: [Valitse]
lspci -v |grep audio

Koodia: [Valitse]
aplay -l
En ole mikään welho linuxin kanssa mutta aika kova googlettamaan... ;D
Sitä vistaan siirtymistä en kyllä vielä harkitsisi... se nimittäin tuppaa ainakin omassa lähipiirissä olemaan todella kokonaisvaltainen ratkaisu, minäkin kärsin jatkuvasti lähisukulaisteni käyttämästä vistasta... :'(



luisfigo

  • Käyttäjä
  • Viestejä: 42
    • Profiili
Fujitsu-Siemens Xi 1546-24, läppäri ja ihan puhdas asennus Ubuntulle.

cat /etc/modprobe.d/alsabase :

# autoloader aliases
install sound-slot-0 /sbin/modprobe snd-card-0
install sound-slot-1 /sbin/modprobe snd-card-1
install sound-slot-2 /sbin/modprobe snd-card-2
install sound-slot-3 /sbin/modprobe snd-card-3
install sound-slot-4 /sbin/modprobe snd-card-4
install sound-slot-5 /sbin/modprobe snd-card-5
install sound-slot-6 /sbin/modprobe snd-card-6
install sound-slot-7 /sbin/modprobe snd-card-7

# Cause optional modules to be loaded above generic modules
install snd /sbin/modprobe --ignore-install snd && { /sbin/modprobe --quiet snd-ioctl32 ; : ; }
install snd /sbin/modprobe --ignore-install snd && { /sbin/modprobe -Qb snd-seq ; }
install snd-pcm /sbin/modprobe --ignore-install snd-pcm && { /sbin/modprobe --quiet snd-pcm-oss ; : ; }
install snd-mixer /sbin/modprobe --ignore-install snd-mixer && { /sbin/modprobe --quiet snd-mixer-oss ; : ; }
install snd-seq /sbin/modprobe --ignore-install snd-seq && { /sbin/modprobe --quiet snd-seq-midi ; /sbin/modprobe --quiet snd-seq-oss ; : ; }
install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi && { /sbin/modprobe --quiet snd-seq-midi ; : ; }
# Cause optional modules to be loaded above sound card driver modules
install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe -Qb snd-emu10k1-synth ; }
install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe -Qb snd-seq ; }

# Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway)
install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe -Qb saa7134-alsa ; : ; }

# Load snd-seq for devices that don't have hardware midi;
#   Ubuntu #26283, #43682, #56005; works around Ubuntu #34831 for
#   non-Creative Labs PCI hardware
install snd /sbin/modprobe --ignore-install snd && { /sbin/modprobe -Qb snd-seq ; }
# Prevent abnormal drivers from grabbing index 0
options bt87x index=-2
options cx88_alsa index=-2
options saa7134-alsa index=-2
options snd-atiixp-modem index=-2
options snd-intel8x0m index=-2
options snd-via82xx-modem index=-2
options snd-usb-audio index=-2
options snd-usb-usx2y index=-2
options snd-usb-caiaq index=-2
# Ubuntu #62691, enable MPU for snd-cmipci
options snd-cmipci mpu_port=0x330 fm_port=0x388
# Keep snd-pcsp from beeing loaded as first soundcard
options snd-pcsp index=-2



lspci -v |grep audio 
:

Ei mitään.


aplay -l

**** Luettelo PLAYBACK laitteista ****
kortti 0: Intel [HDA Intel], laite 0: ALC880 Analog [ALC880 Analog]
  Alalaitteet: 1/1
  Alalaite #0: subdevice #0
kortti 0: Intel [HDA Intel], laite 1: ALC880 Digital [ALC880 Digital]
  Alalaitteet: 1/1
  Alalaite #0: subdevice #0
kortti 0: Intel [HDA Intel], laite 6: Si3054 Modem [Si3054 Modem]
  Alalaitteet: 1/1
  Alalaite #0: subdevice #0




Siis tuo ALC880 löytyy Äänivalikosta mutta ei tule ääniä vaikka mitä vaihtoehtoa sieltä ruksaisin päälle ???






timsku

  • Käyttäjä
  • Viestejä: 225
    • Profiili
Googletin hieman, jonkin verran löytyi tietoa ääniongelmista juuri tuolla ALC880 piirillä. Jos mikserissä kaikki on ok, on varmaan seuraava vaihe kokeilla /etc/modprobe.d/alsa-base tiedoston säätämistä. Tuossa tiedostossa voi asetella optioita kernelin äänimodulille. Täältä löytyy lista optioista, joita voisi tuolle snd-hda-intel modulille tarjota: http://www.mjmwired.net/kernel/Documentation/sound/alsa/ALSA-Configuration.txt#739/etc/modprobe.d/alsabase
Ihan vastaavasta fujitsusta ei tietoa löytynyt mutta ALC880 piirillä toimivia olivat saaneet toimimaan lisäämällä options snd-hda-intel model=fujitsu tai options snd-hda-intel model=auto

Tuo optioiden lisääminen menee suurinpiirtein seuraavasti:
1. sudo nano /etc/modprobe.d/alsa-base #Avataan nano editorilla tiedosto root-oikeuksilla
2. Lisätään haluttu optio, aluksi vaikka options snd-hda-intel model=fujitsu
3. Painetaan ctrl + o, nano kysyy tiedostoa johon tallennetaan, enterin painaminen riittää tässä tapauksessa.
4. ctrl + x, poistutaan nanosta
5.  Komennetaan sudo rmmod snd-hda-intel #poistaa kernelin modulin käytöstä
6. Komennetaan sudo modprobe snd-hda-intel #otetaan moduli käyttöön lisätyllä optiolla
7. Testataan...

Jos vielä katsoisit mitä lspci -vv tulostaa, riittää pelkkä ALC880:tä koskeva pätkä...
Joskus myös dmesg-käskyn tulosteessa saattaa olla jotain vinkkiä...

luisfigo

  • Käyttäjä
  • Viestejä: 42
    • Profiili
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
   Subsystem: Fujitsu Siemens Computers Device 10ac
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 64 bytes
   Interrupt: pin A routed to IRQ 22
   Region 0: Memory at b0000000 (64-bit, non-prefetchable) [size=16K]
   Capabilities: <access denied>
   Kernel driver in use: HDA Intel
   Kernel modules: snd-hda-intel







luisfigo

  • Käyttäjä
  • Viestejä: 42
    • Profiili
[   18.561204] pci 0000:00:1f.2: PME# disabled
[   18.561263] PCI: 0000:00:1f.3 reg 20 io port: [18e0, 18ff]
[   18.561322] PCI: 0000:01:00.0 reg 10 32bit mmio: [c0000000, cfffffff]
[   18.561329] PCI: 0000:01:00.0 reg 14 io port: [2000, 20ff]
[   18.561335] PCI: 0000:01:00.0 reg 18 32bit mmio: [b0100000, b010ffff]
[   18.561354] PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
[   18.561369] pci 0000:01:00.0: supports D1
[   18.561371] pci 0000:01:00.0: supports D2
[   18.561424] PCI: bridge 0000:00:01.0 io port: [2000, 2fff]
[   18.561428] PCI: bridge 0000:00:01.0 32bit mmio: [b0100000, b01fffff]
[   18.561433] PCI: bridge 0000:00:01.0 64bit mmio pref: [c0000000, cfffffff]
[   18.561496] PCI: bridge 0000:00:1c.0 io port: [0, ffff]
[   18.564036] PCI: bridge 0000:00:1c.0 32bit mmio: [fac00000, febfffff]
[   18.564189] PCI: 0000:04:00.0 reg 10 32bit mmio: [b0200000, b0200fff]
[   18.564398] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[   18.564411] pci 0000:04:00.0: PME# disabled
[   18.564469] PCI: bridge 0000:00:1c.2 32bit mmio: [b0200000, b02fffff]
[   18.564534] PCI: 0000:05:04.0 reg 10 32bit mmio: [b0304000, b03047ff]
[   18.564544] PCI: 0000:05:04.0 reg 14 32bit mmio: [b0300000, b0303fff]
[   18.564604] pci 0000:05:04.0: supports D1
[   18.564606] pci 0000:05:04.0: supports D2
[   18.564608] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot
[   18.564614] pci 0000:05:04.0: PME# disabled
[   18.564658] PCI: 0000:05:05.0 reg 10 io port: [3000, 30ff]
[   18.564667] PCI: 0000:05:05.0 reg 14 32bit mmio: [b0304800, b03048ff]
[   18.564708] PCI: 0000:05:05.0 reg 30 32bit mmio: [0, 1ffff]
[   18.564729] pci 0000:05:05.0: supports D1
[   18.564731] pci 0000:05:05.0: supports D2
[   18.564734] pci 0000:05:05.0: PME# supported from D1 D2 D3hot D3cold
[   18.564739] pci 0000:05:05.0: PME# disabled
[   18.564785] PCI: 0000:05:07.0 reg 10 io port: [3850, 385f]
[   18.564795] PCI: 0000:05:07.0 reg 14 io port: [3840, 384f]
[   18.564805] PCI: 0000:05:07.0 reg 18 io port: [3830, 383f]
[   18.564815] PCI: 0000:05:07.0 reg 1c io port: [3820, 382f]
[   18.564825] PCI: 0000:05:07.0 reg 20 io port: [3800, 381f]
[   18.564835] PCI: 0000:05:07.0 reg 24 io port: [3400, 34ff]
[   18.564911] pci 0000:00:1e.0: transparent bridge
[   18.564916] PCI: bridge 0000:00:1e.0 io port: [3000, 3fff]
[   18.564922] PCI: bridge 0000:00:1e.0 32bit mmio: [b0300000, b03fffff]
[   18.564954] bus 00 -> node 0
[   18.564961] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   18.565348] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[   18.565511] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[   18.565668] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[   18.565842] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[   18.568211] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[   18.568292] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[   18.568420] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[   18.568547] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[   18.568673] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[   18.568801] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[   18.568928] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 *4 5 6 7 10 12 14 15)
[   18.569054] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[   18.569131] Linux Plug and Play Support v0.97 (c) Adam Belay
[   18.569131] pnp: PnP ACPI init
[   18.569131] ACPI: bus type pnp registered
[   18.576601] pnp 00:06: io resource (0x2e-0x2f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x4e-0x4f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x61-0x61) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x63-0x63) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x65-0x65) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x67-0x67) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x70-0x70) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x80-0x80) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x92-0x92) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0xb2-0xb3) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x680-0x69f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x800-0x80f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x1000-0x107f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x1180-0x11bf) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:06: io resource (0x1640-0x164f) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:07: io resource (0x6a0-0x6af) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp 00:07: io resource (0x6b0-0x6ff) overlaps 0000:00:1c.0 BAR 7 (0x0-0xffff), disabling
[   18.576601] pnp: PnP ACPI: found 11 devices
[   18.576601] ACPI: ACPI bus type pnp unregistered
[   18.576601] PnPBIOS: Disabled by ACPI PNP
[   18.576601] PCI: Using ACPI for IRQ routing
[   18.576601] pci 0000:00:1c.0: BAR 7: can't allocate resource
[   18.584041] NET: Registered protocol family 8
[   18.584044] NET: Registered protocol family 20
[   18.584061] NetLabel: Initializing
[   18.584061] NetLabel:  domain hash size = 128
[   18.584061] NetLabel:  protocols = UNLABELED CIPSOv4
[   18.584076] NetLabel:  unlabeled traffic allowed by default
[   18.584084] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[   18.584090] hpet0: 3 64-bit timers, 14318180 Hz
[   18.585608] tracer: 772 pages allocated for 65536 entries of 48 bytes
[   18.585611]    actual entries 65620
[   18.585701] AppArmor: AppArmor Filesystem Enabled
[   18.588041] Switched to high resolution mode on CPU 0
[   18.588594] Switched to high resolution mode on CPU 1
[   18.592024] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[   18.592028] system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
[   18.592032] system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
[   18.592035] system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
[   18.592039] system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved
[   18.592042] system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved
[   18.592045] system 00:01: iomem range 0xfed40000-0xfed44fff could not be reserved
[   18.592049] system 00:01: iomem range 0xfed45000-0xfed8ffff could not be reserved
[   18.592058] system 00:04: iomem range 0xfed00000-0xfed003ff could not be reserved
[   18.627295] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[   18.627299] pci 0000:00:01.0:   IO window: 0x2000-0x2fff
[   18.627304] pci 0000:00:01.0:   MEM window: 0xb0100000-0xb01fffff
[   18.627308] pci 0000:00:01.0:   PREFETCH window: 0x000000c0000000-0x000000cfffffff
[   18.627314] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[   18.627316] pci 0000:00:1c.0:   IO window: disabled
[   18.627322] pci 0000:00:1c.0:   MEM window: 0xfac00000-0xfebfffff
[   18.627328] pci 0000:00:1c.0:   PREFETCH window: disabled
[   18.627336] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[   18.627338] pci 0000:00:1c.2:   IO window: disabled
[   18.627345] pci 0000:00:1c.2:   MEM window: 0xb0200000-0xb02fffff
[   18.627350] pci 0000:00:1c.2:   PREFETCH window: disabled
[   18.627359] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[   18.627363] pci 0000:00:1e.0:   IO window: 0x3000-0x3fff
[   18.627370] pci 0000:00:1e.0:   MEM window: 0xb0300000-0xb03fffff
[   18.627376] pci 0000:00:1e.0:   PREFETCH window: 0x00000088000000-0x000000880fffff
[   18.627392] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   18.627396] pci 0000:00:01.0: setting latency timer to 64
[   18.627405] pci 0000:00:1c.0: enabling device (0000 -> 0002)
[   18.627411] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   18.627418] pci 0000:00:1c.0: setting latency timer to 64
[   18.627426] pci 0000:00:1c.2: enabling device (0000 -> 0002)
[   18.627432] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   18.627439] pci 0000:00:1c.2: setting latency timer to 64
[   18.627448] pci 0000:00:1e.0: setting latency timer to 64
[   18.627452] bus: 00 index 0 io port: [0, ffff]
[   18.627454] bus: 00 index 1 mmio: [0, ffffffff]
[   18.627456] bus: 01 index 0 io port: [2000, 2fff]
[   18.627459] bus: 01 index 1 mmio: [b0100000, b01fffff]
[   18.627461] bus: 01 index 2 mmio: [c0000000, cfffffff]
[   18.627463] bus: 01 index 3 mmio: [0, 0]
[   18.627465] bus: 02 index 0 mmio: [0, ffff]
[   18.627468] bus: 02 index 1 mmio: [fac00000, febfffff]
[   18.627470] bus: 02 index 2 mmio: [0, 0]
[   18.627472] bus: 02 index 3 mmio: [0, 0]
[   18.627474] bus: 04 index 0 mmio: [0, 0]
[   18.627476] bus: 04 index 1 mmio: [b0200000, b02fffff]
[   18.627478] bus: 04 index 2 mmio: [0, 0]
[   18.627480] bus: 04 index 3 mmio: [0, 0]
[   18.627482] bus: 05 index 0 io port: [3000, 3fff]
[   18.627485] bus: 05 index 1 mmio: [b0300000, b03fffff]
[   18.627487] bus: 05 index 2 mmio: [88000000, 880fffff]
[   18.627489] bus: 05 index 3 io port: [0, ffff]
[   18.627491] bus: 05 index 4 mmio: [0, ffffffff]
[   18.627500] NET: Registered protocol family 2
[   18.640054] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   18.640297] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   18.640704] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   18.640931] TCP: Hash tables configured (established 131072 bind 65536)
[   18.640934] TCP reno registered
[   18.644086] NET: Registered protocol family 1
[   18.644210] checking if image is initramfs... it is
[   19.432246] Freeing initrd memory: 8463k freed
[   19.432639] Simple Boot Flag at 0x36 set to 0x1
[   19.433573] audit: initializing netlink socket (disabled)
[   19.433602] type=2000 audit(1224941231.432:1): initialized
[   19.440039] highmem bounce pool size: 64 pages
[   19.440046] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[   19.442788] VFS: Disk quotas dquot_6.5.1
[   19.442887] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   19.443008] msgmni has been set to 1743
[   19.443142] io scheduler noop registered
[   19.443145] io scheduler anticipatory registered
[   19.443148] io scheduler deadline registered
[   19.443161] io scheduler cfq registered (default)
[   19.443280] pci 0000:01:00.0: Boot video device
[   19.443410] pcieport-driver 0000:00:01.0: setting latency timer to 64
[   19.443451] pcieport-driver 0000:00:01.0: found MSI capability
[   19.443487] pci_express 0000:00:01.0:pcie00: allocate port service
[   19.443536] pci_express 0000:00:01.0:pcie03: allocate port service
[   19.443638] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[   19.443689] pcieport-driver 0000:00:1c.0: found MSI capability
[   19.443738] pci_express 0000:00:1c.0:pcie00: allocate port service
[   19.443791] pci_express 0000:00:1c.0:pcie02: allocate port service
[   19.443839] pci_express 0000:00:1c.0:pcie03: allocate port service
[   19.443960] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[   19.444011] pcieport-driver 0000:00:1c.2: found MSI capability
[   19.444061] pci_express 0000:00:1c.2:pcie00: allocate port service
[   19.444110] pci_express 0000:00:1c.2:pcie02: allocate port service
[   19.444157] pci_express 0000:00:1c.2:pcie03: allocate port service
[   19.444556] isapnp: Scanning for PnP cards...
[   19.798356] isapnp: No Plug & Play device found
[   19.836744] hpet_resources: 0xfed00000 is busy
[   19.836815] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[   19.839242] brd: module loaded
[   19.839316] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   19.839455] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[   19.845456] i8042.c: Detected active multiplexing controller, rev 1.1.
[   19.846102] serio: i8042 KBD port at 0x60,0x64 irq 1
[   19.846109] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   19.846112] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   19.846115] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   19.846118] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   19.848146] mice: PS/2 mouse device common for all mice
[   19.848301] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[   19.848332] rtc0: alarms up to one month, y3k, hpet irqs
[   19.848473] EISA: Probing bus 0 at eisa.0
[   19.848479] Cannot allocate resource for EISA slot 1
[   19.848483] Cannot allocate resource for EISA slot 2
[   19.848485] Cannot allocate resource for EISA slot 3
[   19.848508] EISA: Detected 0 cards.
[   19.848512] cpuidle: using governor ladder
[   19.848515] cpuidle: using governor menu
[   19.849069] TCP cubic registered
[   19.849098] Using IPI No-Shortcut mode
[   19.849293] registered taskstats version 1
[   19.849415]   Magic number: 12:655:433
[   19.849532] rtc_cmos 00:08: setting system clock to 2008-10-25 13:27:12 UTC (1224941232)
[   19.849536] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   19.849538] EDD information not available.
[   19.849790] Freeing unused kernel memory: 424k freed
[   19.849830] Write protecting the kernel text: 2576k
[   19.849858] Write protecting the kernel read-only data: 936k
[   19.892304] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[   19.988332] fuse init (API version 7.9)
[   20.060544] ACPI: SSDT 7FE95897, 01AF (r1  PmRef  Cpu0Ist     3000 INTL 20050624)
[   20.060933] ACPI: SSDT 7FE95647, 01CB (r1  PmRef  Cpu0Cst     3001 INTL 20050624)
[   20.061550] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   20.061614] processor ACPI0007:00: registered as cooling_device0
[   20.061619] ACPI: Processor [CPU0] (supports 8 throttling states)
[   20.062019] ACPI: SSDT 7FE95A46, 0089 (r1  PmRef  Cpu1Ist     3000 INTL 20050624)
[   20.062379] ACPI: SSDT 7FE95812, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20050624)
[   20.068002] Marking TSC unstable due to TSC halts in idle
[   20.151701] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[   20.151789] processor ACPI0007:01: registered as cooling_device1
[   20.151796] ACPI: Processor [CPU1] (supports 8 throttling states)
[   20.155114] thermal LNXTHERM:01: registered as thermal_zone0
[   20.157242] ACPI: Thermal Zone [THRM] (35 C)
[   20.188236] device-mapper: uevent: version 1.0.3
[   20.188481] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[   20.530571] usbcore: registered new interface driver usbfs
[   20.530596] usbcore: registered new interface driver hub
[   20.530647] usbcore: registered new device driver usb
[   20.532974] USB Universal Host Controller Interface driver v3.0
[   20.533034] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   20.533044] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[   20.533048] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   20.533092] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   20.533130] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[   20.533285] usb usb1: configuration #1 chosen from 1 choice
[   20.533318] hub 1-0:1.0: USB hub found
[   20.533324] hub 1-0:1.0: 2 ports detected
[   20.612097] No dock devices found.
[   20.627550] SCSI subsystem initialized
[   20.645176] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   20.645187] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[   20.645192] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   20.645220] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   20.645260] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[   20.645360] usb usb2: configuration #1 chosen from 1 choice
[   20.645390] hub 2-0:1.0: USB hub found
[   20.645398] hub 2-0:1.0: 2 ports detected
[   20.652242] libata version 3.00 loaded.
[   20.852349] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   20.852361] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[   20.852365] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   20.852394] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   20.852437] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[   20.852542] usb usb3: configuration #1 chosen from 1 choice
[   20.852571] hub 3-0:1.0: USB hub found
[   20.852581] hub 3-0:1.0: 2 ports detected
[   20.956359] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[   20.956373] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[   20.956378] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   20.956407] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   20.956449] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[   20.956553] usb usb4: configuration #1 chosen from 1 choice
[   20.956586] hub 4-0:1.0: USB hub found
[   20.956594] hub 4-0:1.0: 2 ports detected
[   20.964059] usb 2-2: new full speed USB device using uhci_hcd and address 2
[   21.143628] usb 2-2: configuration #1 chosen from 1 choice
[   21.164539] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   21.164556] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[   21.164561] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   21.164590] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[   21.168500] ehci_hcd 0000:00:1d.7: debug port 1
[   21.168509] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[   21.168517] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb0004000
[   21.184026] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   21.184192] usb usb5: configuration #1 chosen from 1 choice
[   21.184223] hub 5-0:1.0: USB hub found
[   21.184232] hub 5-0:1.0: 8 ports detected
[   21.300093] usb 2-2: USB disconnect, address 2
[   21.392375] pata_acpi 0000:00:1f.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   21.392410] pata_acpi 0000:00:1f.1: setting latency timer to 64
[   21.392425] pata_acpi 0000:00:1f.1: PCI INT B disabled
[   21.392489] ahci 0000:00:1f.2: version 3.0
[   21.392499] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   21.392601] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
[   21.392605] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[   21.392611] ahci 0000:00:1f.2: setting latency timer to 64


luisfigo

  • Käyttäjä
  • Viestejä: 42
    • Profiili
[   21.392798] scsi0 : ahci
[   21.392934] scsi1 : ahci
[   21.393045] scsi2 : ahci
[   21.393868] scsi3 : ahci
[   21.393986] ata1: SATA max UDMA/133 abar m1024@0xb0004400 port 0xb0004500 irq 220
[   21.393989] ata2: DUMMY
[   21.393992] ata3: SATA max UDMA/133 abar m1024@0xb0004400 port 0xb0004600 irq 220
[   21.393994] ata4: DUMMY
[   21.500067] Clocksource tsc unstable (delta = -423939743 ns)
[   21.713076] ata1: SATA link down (SStatus 0 SControl 300)
[   21.968064] usb 2-2: new full speed USB device using uhci_hcd and address 3
[   22.048084] ata3: SATA link down (SStatus 0 SControl 300)
[   22.064137] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[   22.064153] r8169 0000:05:05.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[   22.064474] eth0: RTL8169sb/8110sb at 0xf8924800, 00:03:0d:4b:db:21, XID 10000000 IRQ 19
[   22.068235] sata_via 0000:05:07.0: version 2.3
[   22.068252] sata_via 0000:05:07.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   22.068292] sata_via 0000:05:07.0: routed to hard irq line 7
[   22.070044] scsi4 : sata_via
[   22.076072] scsi5 : sata_via
[   22.076168] scsi6 : sata_via
[   22.076220] ata5: SATA max UDMA/133 port i16@0x3850 bmdma 0x3800 irq 17
[   22.076224] ata6: SATA max UDMA/133 port i16@0x3840 bmdma 0x3808 irq 17
[   22.076227] ata7: PATA max UDMA/133 port i16@0x3830 bmdma 0x3810 irq 17
[   22.141453] usb 2-2: configuration #1 chosen from 1 choice
[   22.380072] usb 4-1: new low speed USB device using uhci_hcd and address 2
[   22.396129] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   22.561634] usb 4-1: configuration #1 chosen from 1 choice
[   22.579705] usbcore: registered new interface driver hiddev
[   22.631229] input: Microsoft Microsoft Wireless Optical Mouse� 1.00 as /devices/pci0000:00/0000:00:1d.3/usb4/4-1/4-1:1.0/input/input2
[   22.631531] input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse� 1.00] on usb-0000:00:1d.3-1
[   22.631552] usbcore: registered new interface driver usbhid
[   22.631555] usbhid: v2.6:USB HID core driver
[   22.784304] ata5.00: ATA-7: WDC WD1200BEVS-07LAT0, 01.06M01, max UDMA/133
[   22.784308] ata5.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/1)
[   22.792750] ata5.00: configured for UDMA/133
[   23.112127] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   23.498861] ata6.00: ATA-7: WDC WD1200BEVS-07LAT0, 01.06M01, max UDMA/133
[   23.498865] ata6.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/1)
[   23.504754] ata6.00: configured for UDMA/133
[   23.672255] scsi 4:0:0:0: Direct-Access     ATA      WDC WD1200BEVS-0 01.0 PQ: 0 ANSI: 5
[   23.672832] scsi 5:0:0:0: Direct-Access     ATA      WDC WD1200BEVS-0 01.0 PQ: 0 ANSI: 5
[   23.672941] ohci1394 0000:05:04.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   23.722690] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[b0304000-b03047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[   23.723491] scsi 4:0:0:0: Attached scsi generic sg0 type 0
[   23.723534] scsi 5:0:0:0: Attached scsi generic sg1 type 0
[   23.732001] ata_piix 0000:00:1f.1: version 2.12
[   23.732018] ata_piix 0000:00:1f.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   23.732067] ata_piix 0000:00:1f.1: setting latency timer to 64
[   23.732400] scsi7 : ata_piix
[   23.732490] scsi8 : ata_piix
[   23.733205] ata8: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1880 irq 14
[   23.733209] ata9: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1888 irq 15
[   23.751418] Driver 'sd' needs updating - please use bus_type methods
[   23.751653] sd 4:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[   23.751676] sd 4:0:0:0: [sda] Write Protect is off
[   23.751679] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   23.751720] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   23.751819] sd 4:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[   23.751841] sd 4:0:0:0: [sda] Write Protect is off
[   23.751845] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   23.751884] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   23.751889]  sda: sda1
[   23.807585] sd 4:0:0:0: [sda] Attached SCSI disk
[   23.807680] sd 5:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
[   23.807706] sd 5:0:0:0: [sdb] Write Protect is off
[   23.807709] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   23.807755] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   23.807835] sd 5:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
[   23.807860] sd 5:0:0:0: [sdb] Write Protect is off
[   23.807863] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   23.807910] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   23.807915]  sdb:<6>ata8.00: ATAPI: Optiarc DVD RW AD-7540A, 1.42, max UDMA/33
[   23.912515] ata8.00: configured for UDMA/33
[   23.912565] ata9: port disabled. ignoring.
[   23.918368] scsi 7:0:0:0: CD-ROM            Optiarc  DVD RW AD-7540A  1.42 PQ: 0 ANSI: 5
[   23.918535] scsi 7:0:0:0: Attached scsi generic sg2 type 5
[   23.923486]  sdb1 sdb2 <<4>Driver 'sr' needs updating - please use bus_type methods
[   23.954725]  sdb5 >
[   23.954904] sd 5:0:0:0: [sdb] Attached SCSI disk
[   23.977823] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[   23.977828] Uniform CD-ROM driver Revision: 3.20
[   23.977938] sr 7:0:0:0: Attached scsi CD-ROM sr0
[   24.248579] PM: Starting manual resume from disk
[   24.248583] PM: Resume from partition 8:21
[   24.248585] PM: Checking hibernation image.
[   24.248810] PM: Resume from disk failed.
[   24.329910] kjournald starting.  Commit interval 5 seconds
[   24.329921] EXT3-fs: mounted filesystem with ordered data mode.
[   24.992195] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00030d4972008316]
[   32.406151] udevd version 124 started
[   32.985446] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   33.023836] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   33.071748] Linux agpgart interface v0.103
[   33.160854] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[   33.192485] ACPI: Power Button (FF) [PWRF]
[   33.192630] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[   33.192700] ACPI: Lid Switch [liD0]
[   33.192777] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[   33.224034] ACPI: Power Button (CM) [PWRB]
[   33.224179] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6
[   33.256034] ACPI: Sleep Button (CM) [SLPB]
[   33.256980] ACPI: AC Adapter [AC0] (on-line)
[   33.266391] ACPI: Battery Slot [BAT0] (battery present)
[   33.266555] ACPI: WMI: Mapper loaded
[   33.334486] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/device:02/input/input7
[   33.348034] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   33.348800] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:07/input/input8
[   33.380032] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   33.611695] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   33.665554] [fglrx] Maximum main memory to use for locked dma buffers: 1895 MBytes.
[   33.666198] [fglrx]   vendor: 1002 device: 7102 count: 1
[   33.673328] [fglrx] ioport: bar 1, base 0x2000, size: 0x100
[   33.673346] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   33.673352] pci 0000:01:00.0: setting latency timer to 64
[   33.674615] [fglrx] PAT is enabled successfully!
[   33.674649] [fglrx] module loaded - fglrx 8.54.3 [Oct 10 2008] with 1 minors
[   33.838888] Bluetooth: Core ver 2.13
[   33.887403] NET: Registered protocol family 31
[   33.887407] Bluetooth: HCI device and connection manager initialized
[   33.887411] Bluetooth: HCI socket layer initialized
[   33.981058] intel_rng: FWH not detected
[   34.026060] Bluetooth: Generic Bluetooth USB driver ver 0.3
[   34.026706] usbcore: registered new interface driver btusb
[   34.215377] input: PC Speaker as /devices/platform/pcspkr/input/input9
[   34.253256] iTCO_vendor_support: vendor-support=0
[   34.339109] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   34.358403] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[   34.358408] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[   34.359101] iwl3945 0000:04:00.0: enabling device (0000 -> 0002)
[   34.359113] iwl3945 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   34.359133] iwl3945 0000:04:00.0: setting latency timer to 64
[   34.359155] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[   34.439744] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[   34.440447] phy0: Selected rate control algorithm 'iwl-3945-rs'
[   34.744252] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   34.744289] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   34.789495] iwl3945 0000:04:00.0: PCI INT A disabled
[   34.797430] Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa0b1, caps: 0xa04713/0x20040a
[   34.838249] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input10
[   34.862975] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[   34.863071] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   36.361688] lp: driver loaded but no devices found
[   36.512686] Adding 4803392k swap on /dev/sdb5.  Priority:-1 extents:1 across:4803392k
[   37.061353] EXT3 FS on sdb1, internal journal
[   38.274323] type=1505 audit(1224930451.127:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4445
[   38.448840] type=1505 audit(1224930451.299:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4450
[   38.449071] type=1505 audit(1224930451.303:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4450
[   38.617192] ip_tables: (C) 2000-2006 Netfilter Core Team
[   40.287442] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   40.413079] apm: BIOS not found.
[   40.778160] ppdev: user-space parallel port driver
[   43.247734] Bluetooth: L2CAP ver 2.11
[   43.247747] Bluetooth: L2CAP socket layer initialized
[   43.263733] Bluetooth: SCO (Voice Link) ver 0.6
[   43.263747] Bluetooth: SCO socket layer initialized
[   43.298360] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   43.298373] Bluetooth: BNEP filters: protocol multicast
[   43.344582] Bridge firewalling registered
[   43.345638] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[   43.359115] Bluetooth: RFCOMM socket layer initialized
[   43.359140] Bluetooth: RFCOMM TTY layer initialized
[   43.359144] Bluetooth: RFCOMM ver 1.10
[   47.516611] r8169: eth0: link down
[   47.726197] iwl3945 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   47.726365] iwl3945 0000:04:00.0: restoring config space at offset 0x1 (was 0x100002, writing 0x100006)
[   47.727431] firmware: requesting iwlwifi-3945-1.ucode
[   47.959335] Registered led device: iwl-phy0:radio
[   47.959552] Registered led device: iwl-phy0:assoc
[   47.959976] Registered led device: iwl-phy0:RX
[   47.960302] Registered led device: iwl-phy0:TX
[   48.077192] NET: Registered protocol family 17
[   50.248074] wlan0: authenticate with AP 0a:0c:c3:72:0d:e1
[   50.249856] wlan0: authenticated
[   50.249866] wlan0: associate with AP 0a:0c:c3:72:0d:e1
[   50.254919] wlan0: RX AssocResp from 0a:0c:c3:72:0d:e1 (capab=0x421 status=0 aid=2)
[   50.254928] wlan0: associated
[   50.275920] wlan0: disassociating by local choice (reason=3)
[   71.826074] wlan0: deauthenticated
[   71.826608] wlan0: authenticate with AP 0a:0c:c3:72:0d:e1
[   71.829657] wlan0: authenticated
[   71.829668] wlan0: associate with AP 0a:0c:c3:72:0d:e1
[   71.835123] wlan0: RX ReassocResp from 0a:0c:c3:72:0d:e1 (capab=0x421 status=0 aid=2)
[   71.835133] wlan0: associated
[   71.835950] wlan0: disassociating by local choice (reason=3)
[   74.057776] CPU0 attaching NULL sched-domain.
[   74.057795] CPU1 attaching NULL sched-domain.
[   74.061149] CPU0 attaching sched-domain:
[   74.061159]  domain 0: span 0-1 level MC
[   74.061164]   groups: 0 1
[   74.061175] CPU1 attaching sched-domain:
[   74.061179]  domain 0: span 0-1 level MC
[   74.061184]   groups: 1 0
[   95.584776] wlan0: deauthenticated
[   95.585002] wlan0: authenticate with AP 0a:0c:c3:72:0d:e1
[   95.587253] wlan0: authenticated
[   95.587266] wlan0: associate with AP 0a:0c:c3:72:0d:e1
[   95.594241] wlan0: authenticate with AP 00:1a:9f:03:5b:54
[   95.596391] wlan0: authenticate with AP 00:1a:9f:03:5b:54
[   95.597564] wlan0: authenticated
[   95.597574] wlan0: associate with AP 00:1a:9f:03:5b:54
[   95.608453] wlan0: RX AssocResp from 00:1a:9f:03:5b:54 (capab=0x471 status=0 aid=1)
[   95.608463] wlan0: associated
[   95.807375] padlock: VIA PadLock not detected.
[  123.473728] type=1503 audit(1224930536.327:5): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/7531/net/" pid=7531 profile="/usr/sbin/cupsd"
[  124.534941] type=1503 audit(1224930537.386:6): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/7553/net/" pid=7553 profile="/usr/sbin/cupsd"
[  124.631045] NET: Registered protocol family 10
[  124.633566] lo: Disabled Privacy Extensions
[  124.636121] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  124.639088] type=1503 audit(1224930537.490:7): operation="socket_create" family="ax25" sock_type="dgram" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  124.639109] type=1503 audit(1224930537.490:8): operation="socket_create" family="netrom" sock_type="seqpacket" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  124.639120] type=1503 audit(1224930537.490:9): operation="socket_create" family="rose" sock_type="dgram" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  124.639132] type=1503 audit(1224930537.490:10): operation="socket_create" family="ipx" sock_type="dgram" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  124.639144] type=1503 audit(1224930537.490:11): operation="socket_create" family="appletalk" sock_type="dgram" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  124.639156] type=1503 audit(1224930537.490:12): operation="socket_create" family="econet" sock_type="dgram" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  124.639167] type=1503 audit(1224930537.490:13): operation="socket_create" family="ash" sock_type="dgram" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  124.639179] type=1503 audit(1224930537.490:14): operation="socket_create" family="x25" sock_type="seqpacket" protocol=0 pid=7553 profile="/usr/sbin/cupsd"
[  134.768062] wlan0: no IPv6 routers present

babau

  • Käyttäjä
  • Viestejä: 2
    • Profiili
Ubuntu 8.10 on käyttiksenä. Ja Realtek ALC880-äänipiirin asennus ei ota toimiakseen. 8.04 Ubuntulla sama ongelma.
Miten saisin äänet kuuluviin?

Olen ihan n00b tämän linuxin kanssa ja muuten olen tykännyt tästä mutta äänien toimimattomuuden takia vaihtuu kohta taas Vistaan takaisin :-\


..Ootko kokeillu tätä:

Man skriver in detta i terminalen:

    sudo apt-get install module-assistant
    sudo m-a update
    sudo m-a prepare
    sudo m-a a-i alsa



och startar om datorn sen. Sen funkar det. :)

..tää löytyi :  http://ubuntu-se.org/phpBB3/viewtopic.php?f=194&t=26728

..ja se on laina sivulta :   http://kubasik.net/blog/2008/03/31/sound-problems-in-ubuntu-hardy/
joka ei just nyt ole auki , ..(kokeile myöhemmin..)..

..täs on viel yks lisää:

..Try the following guide for troubleshooting sound problems:

http://ubuntuforums.org/showthread.php?t=205449

..Jos mä oon tajunnu "the problem" oikein, niin   "the sound modules" pitää  "invoke" tuolla  "init command"..

.täs loytyi viel yks sivu:

  http://linux.dell.com/wiki/index.php/Ubuntu_8.04/Issues/No_Sound_After_Distribution_Or_Kernel_Upgrade

Ubuntu 8.04/Issues/No Sound After Distribution Or Kernel Upgrade
From DellLinuxWiki
< Ubuntu 8.04
Jump to: navigation, search


Description: No sound after upgrade from Ubuntu 7.10 or upgrade to kernel 2.4.24-17.
Systems Affected: Inspiron E1505n, 1420n and 1525n.
Impact: No sound from speakers or headphones.
Fix: If doing a distribution upgrade from Ubuntu 7.10 to 8.04, remove old modem driver. If you're already running Ubuntu 8.04 and are upgrading from kernel 2.4.24-16 to 2.4.24-17, upgrade to kernel 2.4.24-18 or above:

Upgrading from Ubuntu 7.10 to 8.04

Remove old modem driver for Ubuntu 7.10:

$ sudo dpkg -r hsfmodem

Remove linux-backports-modules package for kernel 2.6.22-14-generic:

$ sudo dpkg -r linux-backports-modules-2.6.22-14-generic

Restore name of sound driver that old modem driver renamed:

$ cd /lib/modules/`uname -r`/ubuntu/sound/alsa-driver/pci/hda
$ sudo mv snd-hda-intel.ko.REPLACEDBYhsfmodem snd-hda-intel.ko

Remove old sound drivers from kernel module directory:

$ cd /lib/modules/`uname -r`/updates
$ sudo rm snd-hda-intel.ko
$ sudo rm snd-hda-codec.ko

Rebuild initrd and reboot:

$ sudo depmod -a
$ sudo update-initramfs -u
$ sudo reboot

If you want to install the new modem driver for Ubuntu 8.04, see here .

If already running Ubuntu 8.04 and upgrading to kernel 2.6.24-17-generic

Restore name of sound driver that old modem driver renamed:

$ cd /lib/modules/2.6.24-17-generic/ubuntu/sound/alsa-driver/pci/hda
$ sudo mv snd-hda-intel.ko.REPLACEDBYhsfmodem snd-hda-intel.ko

Remove old sound drivers from kernel module directory:

$ cd /lib/modules/2.6.24-17-generic/updates
$ sudo rm snd-hda-intel.ko
$ sudo rm snd-hda-codec.ko

Rebuild initrd and reboot:

$ sudo depmod -a
$ sudo update-initramfs -u
$ sudo reboot

The modem should now be recognized and fully functional.

luisfigo

  • Käyttäjä
  • Viestejä: 42
    • Profiili
  sudo apt-get install module-assistant
    sudo m-a update
    sudo m-a prepare
    sudo m-a a-i alsa


Tällä pätkällä alkoi toimimaan, kiitos kaikille tasapuolisesti!